mt07 dash relocation by 3d models

... this speaker. You can customize this like I did from the original if needed for a specific speaker. I also have a 5mm version of this, but it was too thick for this particular speaker. The 5mm prevented the dash cover from snapping down over it.

Dash 5 inches TFT HDMI, to be used with the PeterMakesThings Dashboard. (https://www.thingiverse.com/thing:4553011) Thanks for your work Peter! ... Parts List: -Screen:...

This is as direct a recreation of the original dash vents as I have been able to design. I have not been able to test it yet due to a busy schedule hence the "Experimental" in the name. It is a two-part design to prevent this from having massive...

Replacement Mount for the Garmin Dash Cam 45/55. To ensure a precise fit, I carefully tilted the part approximately 25 degrees around the Y-Axis to optimize the print quality on the top section. Subsequently, I sanded down the base to achieve a...

Dash mount that I made to keep my binoculars and range finder from sliding off when going over rough terrain while scouting. So far I've only tested my Vortex Viper and Cabelas Intensity on the bino side, but realistically it should fit most all...

This is an insert for the recessed area on the dash on a 2013 F250.  It provides a flat surface to mount a stand for your phone.  Corner stands are included, but are designed for my phone case.  The corner mounts should be easy enough...

I use this phone holder in conjunction with a dash mount designed specifically for my Miata, which I utilize during autocross events for data logging purposes with solostorm. *** Updated 06-15-2018 Upon reviewing the initial print results, I...

First attempt at a Vstom Dash to hold meters, switches, whatever. Fitted perfectly first time, you have to remove the 4 x bolt covers for the handle bar and the protrusions fit into the bolt heads (as the old covers did). I found the fit to be...

VW Polo dash GPS and Cell holder with bars. Made specifically for the hole in the dashboard of 2008 Polos, but also compatible with other cars that have a similar design. For installation, no smooth surface is required on the dashboard as the...

Here is a set of simplified meshes of the dash of the '97 Diahatsu Hijet S110P. These are cleaned up and simplified meshes, I had to perform quite a bit of post processing since the source files were hundreds of megabytes. I used MeshLab to clean...

Update 6/12/2022: ** -Added a new stand for the screen -Edited back cover Here is a Dash for your G29 steering wheel that uses a HDMI screen, 22 leds and simhub to work. Parts: Bolts and nuts: M3: 2 x Button 20mm long 2 x Button 16mm long 4 x...

Phone or tablet dock designed for table or car's dash. The dock features a container that can be filled with sand or steel to make it heavy and stable. I've created this design specifically for use in my car, where I wanted an easy-to-use solution...

It's specifically designed for this one type of adapter, but I'm happy to report that it fits perfectly with my Dash charger too - so it should work seamlessly with other adapters or purposes as well. ...As you can see from the pictures, I made some...

This is a vibration-free camera mount designed specifically for use as a dash cam in cars, compatible with the Samsung 360 (2017 version) camera. The suspension balls used are identical to those employed in drone gimbals, ensuring seamless...

Double Din Dash Kit for Jeep Chrysler Dodge VW, see below for vehicle fitment. As always, I never put the radio mounting holes due to many different brands available, so you will have to drill your own holes depending on radio fitment. ... Chrysler 200...

I wanted a sturdy dash mount that didn't shake with the wheel vibrations so I ended up designing this. It is bolted through the steering wheel body which means you need to open it up. There is plenty of how to online so I will not go into the...

how to make a digital dash for mx5 miata using a 2012 nexus 7. i have attached both the laser cutting ACAD file, as well as 2 piece STL file for 3D printing, all you need is a nexus 7, 2012/2013. a custom rom for the nexus which allows it to boot up...

The piece that holds my KDLINKS X1 dash cam to the suction cup mount had broke and my camera fell. Designed this as a replacement part.</p> <p>I have included the Fusion 360 file, along with several other formats that will allow you to customize it.

On the 2008-2016 model years, there is a tiny storage tray on the dash. Some trim levels have it so there's just an open tray, other's have it with a door on top of said tray. The units with the hinging door are made of what can only be described as...

On the 2008-2016 model years, there is a tiny storage tray on the dash. Some trim levels have it so there's just an open tray, other's have it with a door on top of said tray. The units with the hinging door are made of what can only be described as...

... This design offers a professional and discreet method for mounting a gauge seamlessly with the interior of the car for just $1.25 in PLA filament and $0.08 of double-sided tape to hold the pod to the dash and the gauge in place within the pod.

I've been searching for a DIY dash button for my FHEM SmartHome system for quite some time. On Thingiverse, I found this [ESP8266 IoT Wifi] button (https://www.thingiverse.com/thing:2803769) that caught my eye. The design of the case and the ability...

The camera is attached to the rearview mirror of the vehicle via the suction cup and adjustable arm provided by Garmin.

This object was created using the innovative 3D design platform, Tinkercad. ...Users can easily edit and modify it directly within their web browser by visiting https://www.tinkercad.com/things/2U7waAcjf4F.

this is a model of the clips thats on the Bmw e46 dashboard best to print in ASA or abs ! ...:) Pla tends to break, caused by the stiffness.. plug and play! ... fits perfect in my own car :)

I made some clever modifications by nudging the tabs slightly outwards, and added my good friend RD's adorable cutie mark for good measure! ...To get that precise look, I decided to print it with a moderate 15% infill level, but to be honest, that...

Fixes to the car by the same geometry adopted by the OEM cluster. ECU fixes with the part bolted from behind (matches the original holes). File pack corresponds to a ZIP with STL files inside: the cluster as pictured on Image 2, "as one" (all...

For my Garmin Nuvi 850 GPS, I created a magnetic mount by customizing another model's design. I added a ball joint for a proper fit and combined the base and ball with superglue, ensuring the right size through scaling. ...Finally, I inserted a rare...

... console. ...To safeguard against screen damage, rubber grommets were strategically placed on areas coming into direct contact with the display. During the printing process, the front of the mount faced downwards and was supported by stabilizers.

As shown in the images, this is a replacement coin tray for the center console of the 3000GT series by Mitsubishi. Recommend printing in ABS and UV painted for protection as sunlight will easily strike this part. 25% infill and 3 walls thick...