mtg playmat tube 3d models

This Little cup is made to close a tube for Card game playmat! For now I'm uploading only one cup, you can print it and close your playmat with! ...Then I'll upload a more complex version with instruction and photo!

Remixed to hold a rolled-up MTG playmat, and to print without supports. I also sliced a cylinder out of the center, to make a smoother inner-surface to slide the mat into. It is very tall, and I had to use my Tevo Tornado to print it. You could...

Remixed to hold a rolled-up MTG playmat, and to print without supports. I also sliced a cylinder out of the center, to make a smoother inner-surface to slide the mat into. It is very tall, and I had to use my Tevo Tornado to print it. You could...

I had tried some of the playmat holders out there and decided to try my had at my own.

... The "Remix" function did not work to link the source files properly....potate-verse at it's finest. ... I split the tube into to pieces to be able to print it on my Ender 3 V2. ...I also added a "reinforcement" ring to enlarge the glued surface area.

... function did not work to link the source files properly....potate-verse at it's finest. ... I split the tube into to pieces to be able to print it on my Ender 3 V2. I also added a "reinforcement" ring to enlarge the glued surface area. ...

This is a remix of: https://www.thingiverse.com/thing:3544399 and: https://www.thingiverse.com/thing:517581 The "Remix" function did not work to link the source files properly....potate-verse at it's finest. I split the tube into to pieces to be able...

njeff's playmat tube was not only too tall for my printer, but was too wide for some of my thinner playmats. I shrunk it to fit thinner playmats, and only 10cm tall. ...Works like a charm.

I have also added in files for a 2-piece tube print so those with smaller printers can also print playmat tubes! Approximately 190mm for each section. ... Full disclaimer: I have not yet printed one of the 2-piece tubes myself, it looks like for the...

Updated February 8th, 2023: Added part Playmat_Tube_Spiral_Top_Short, its 30mm shorter. These parts are interchangeable with my other play-mat tube designs Spots and Stripes. https://www.thingiverse.com/thing:5616827 ...

... These parts are interchangeable with my other play-mat tube designs Stripes and Spiral https://www.thingiverse.com/thing:5616859 https://www.thingiverse.com/thing:5616839 Note: This model was designed to be printed using a .4mm diameter nozzle.

Either version can be made longer adding an extra Centers section, each one will extend the tube by 12.5cm (4.9 inches). These parts are interchangeable with my other play-mat tube designs Spots and Spiral. https://www.thingiverse.com/thing:5616827...

Holder for the Ultra Pro playmat tube (https://www.ultrapro.com/product_info.php?products_id=2298) to keep it from rolling off the table while playing.

Either version can be made longer adding an extra Centers section, each one will extend the tube by 12.5cm (4.9 inches).These parts are interchangeable with my other play-mat tube designs Stripes and SpiralNote:This model was designed to be printed...

Either version can be made longer adding an extra Centers section, each one will extend the tube by 12.5cm (4.9 inches).These parts are interchangeable with my other play-mat tube designs Spots and StripesNote:This model was designed to be printed...

Either version can be made longer adding an extra Centers section, each one will extend the tube by 12.5cm (4.9 inches).These parts are interchangeable with my other play-mat tube designs Spots and SpiralNote:This model was designed to be printed...

Holder for the Ultra Pro playmat tube (https://www.ultrapro.com/product_info.php?products_id=2298) to keep it from rolling off the table while playing. Category: Hobby

You will probably need to print 2 of these, but you may as well try using a single one, and balancing your playmat tube with the help of a wall.Use some common wooden screws to attach it. Will need 2 of those per print.</p><p>The one in the picture...

This is the same diameter as Ultra Pro tubes, but the caps can be used for any 2" diameter tube -- I used these 16.5" long polycarbonate tubes: https://www.amazon.com/dp/B093GS1T7R?ref=ppx_yo2ov_dt_b_product_details&th=1 I made these so my playmat...

No description provided.

a simple playmat holder no support is needed total length is 38cm inner diameter is 4.9 cm

Dicemaster Playmat, Quite big, scale as needed. ... Might do a modification to make it foldable, but that would be a future project.

Dicemaster Playmat, Quite big, scale as needed. Might do a modification to make it foldable, but that would be a future project. ...

This is a basic holder that slides onto the end of the playmat [ you will need two, one for each end] to protect the playmat and its edges when not in use.&nbsp;The gap for the playmat to ‘slot’ into is 9mm, this will fit all standard Pokémon...

A simple, modular life counter for playing Magic the Gathering (or any game that goes to 99 points). The fitting part can be taken out, and as the model is modular, you can print in different colors as you like it. This object was made in...

http://www.thingiverse.com/apps/customizer/run?thing_id=66327 Instructions Using the following options: bottom_text_font = write/orbitron.dxf input = image_size = 20 card_count = 30 top_text_rotation = 0 image_rotation = 0 Move_Top_Text_Up_Down = 60...

I've bored out the original tube design to fit my own Wolverine Storm Regulator as the last 10mm or so was too tight.

A mountable playmat holder that you can screw up on your wall or shelf to store your playmats. Great for collectable card games like Magic the Gathering or Android Netrunner. I've included 3 versions. Playmat Holder - A completely circular one. ...

A mountable playmat holder that you can screw up on your wall or shelf to store your playmats. Great for collectable card games like Magic the Gathering or Android Netrunner.I've included 3 versions.Playmat Holder - A completely circular one. Can be...