multirotormania 3d models
17 3d models found related to multirotormania.thingiverse
I made some trophies for the local Tiny Whoop race series and MRM was a sponsor, so I whipped up this little 3d logo to stick on the trophies.
thingiverse
Parts for the Reaper frame from MultirotorMania.com: 45° Session mount Foot/Motor Protector VTX mount (Hawkeye 200mw) Print with a flexible filament; Sainsmart TPU or Ninjaflex.
thingiverse
I put this together for the Caddx Firefly to mount to the MRM Pocketknife 69. ... https://multirotormania.com/collections/frames/products/mrm-pocketknife-69-micro-fpv-frame 30 degree camera angle.
thingiverse
The following straps work well with this mount:- Yi - http://www.multirotormania.com/fpv/1147-mrm-yi-cam-velcro-strap.html Go Pro - http://www.multirotormania.com/fpv/1146-mrm-gopro-velcro-strap.html Detail - 0.20mm Supports - Yes Print Settings...
thingiverse
... I have to find an easy way to access to the sdcard. I saw that Cleanflight include a tethered function to access to sd card.... Maybe it's the solution. Blackbox board goes from multirotormania. ...I adjust the hole to fit better to the spacer.
pinshape
... I have to find an easy way to access to the sdcard. I saw that Cleanflight include a tethered function to access to sd card.... Maybe it's the solution. Blackbox board goes from multirotormania. ...I adjust the hole to fit better to the spacer.
cults3d
... I have to find an easy way to access to the sdcard. I saw that Cleanflight include a tethered function to access to sd card.... Maybe it's the solution. Blackbox board goes from multirotormania. ... I adjust the hole to fit better to the spacer.
thingiverse
Features Space between screws is 30 mm holes behind the bar for wires, or in the center with a groove to route the wires through the center holes for zip ties (but I afixed the LEDs with hot glue) I got the LED bar from...
thingiverse
http://www.multirotormania.com/frames/1450-mrm-scythe-v2-220mm-x-frame.html These mounts are designed to be printed in TPU!! Printing in a Rigid material (PLA, ABS, etc.) will not result in a functioning part. The session Mount is available in 25, 35...
thingiverse
EDIT: Now the mount for the plastic cased camera is for sale at MRM: http://multirotormania.com/3d-printed-parts/1068-mini-600tvl-mount-for-the-mini-250-quad-zmr.html Shapeways (HS1175): https://www.shapeways.com/product/TRTG556JB Shapeways...
thingiverse
This part was made to mount the DragonFly 32 Micro from MultirotorMania.com to standard 1.2 inch (30 mm) flight controller mounting holes. I use a few well placed dabs of hot glue to seat the flight controller. This mount will hold the FC flat,...
thingiverse
http://www.multirotormania.com/frames/1450-mrm-scythe-v2-220mm-x-frame.html Each file is a Left front or rear arm and should be mirrored after inserting to have a set. The Scythe Set will fit both the Scythe and switchblade. The switchblade set will...
thingiverse
http://www.multirotormania.com/80-colored-nylon- https://www.youtube.com/watch?v=lmNWCqTTtRo Print Settings Notes: HIGHLY recommended to print the frame plates in Taulman 910 nylon. When printed in nylon this frame has proved to be nearly...
thingiverse
More will be added as they are designed.http://www.multirotormania.com/200mm-smaller-micro/1448-mrm-reaper-195220-fpv-racing-frame.html These Mounts are designed to be printed in TPU!! Printing in a Rigid material (PLA, ABS, etc.) will not result in...
thingiverse
http://www.multirotormania.com/frames/1450-mrm-scythe-v2-220mm-x-frame.html All the hoods fit a HS1177 camera. like most hood builds, a low FC and PDB stack height is a must. These hoods are designed to be printed in TPU!! Printing in a Rigid...
thingiverse
http://www.multirotormania.com/200mm-smaller-micro/1448-mrm-reaper-195220-fpv-racing-frame.html These will work in TPU or a rigid material. They can be mounted from the bottom or between the motor and frame. Each arm protector weighs in a 2.6g...
thingiverse
Here are the Video Transmitter and Vertical Antenna Mounts for the MRM Reaper frames.http://www.multirotormania.com/200mm-smaller-micro/1448-mrm-reaper-195220-fpv-racing-frame.html These Mounts are designed to be printed in TPU!! Printing in a Rigid...