nano skyhunter fpv 3d models

This design builds upon the version found at http://www.thingiverse.com/thing:617052 with a critical fix. The original model lacked watertight integrity resulting in failed prints. After modification, it now prints reliably with one notable...

This is based on http://www.thingiverse.com/thing:617052 but is fixed. The original version of this model was not watertight and therefore did not print correctly. This prints properly (the lid is a bit tight though, might rework that in the near...

FPV camera support box for Caddx Turbo Eos V2, compatible with the Martian 2 chassis, featuring two 1cm screws.

I designed this to be able to easily drill holes in an 18650 tray to build some Dave_C Nano Longrange quads. ...

Heroscape: Brandis Skyhunter on base

... Vista Nebula Pro and Nano camera mount. I moved the mounting holes forward and for the 14mm camera (nano size) I made it even lighter, and you do not need any supports to print it. ... The purpose of this is to keep the quad as light as possible.

This is my nano pod design for tinywhoop and toothpick, it fit foxeer pico razer and caddx ant lite. Cam need to be glued inside cause no fixing point. Warning !!! ... This is one pretty hard TPU print, your pinter must be setup right to achieve.

These custom printed pieces from TPU (other flexible materials will work just as well) are designed to fit snugly onto a shrink tube wrapped 18650 pack, then snap into place on the nano talon's wooden tray. The rear section slides into place from the...

Just install the "base" and wiring to the FC on your models and fit the FPV Pod to the model in current use. Compared to the pictures the locking system has been improved and simplified in the stl files.</p><p>A mount/air scoop for the Heewing T1...

I reused the same mounting style but redesigned the case for the Nano 33 Sense version and added a balancer connector port instead of the cable to power the Nano 33. The goggle adapter comes in 2 versions. - DJI Mount_M3 Screws.STL -> this one...

Just install the "base" and wiring to the FC on your models and fit the FPV Pod to the model in current use. Compared to the pictures the locking system has been improved and simplified in the stl files.Now there is also a .STEP file of the base so...

Another one of those, might fit your frame.

Dimension are approximate. ...can be used for reference.

The Compact Converter is an innovative solution that seamlessly integrates a 14mm camera into a 19mm space. ...Developed specifically for the Caddex Turbo EOS1, this adapter also fits similarly sized cameras, providing users with expanded flexibility...

This is a revised model based on KiLLiN-TiMe's original design (https://www.thingiverse.com/thing:1266503). ...The top layer had printing issues, so I modified the file to achieve a smooth print result.

Inspirit this model (https://www.thingiverse.com/thing:5346153), but ше didn't suit me and I made my version.

Remix of Thingiverse's http://www.thingiverse.com/thing:809885 customized for the Micro Motor Warehouse 6mm motors. It's engineered to accommodate a 6mm hole, however the motors are precisely 6.2mm in diameter, so you must carefully bore out the...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

This is a cover for the recessed bay in the top of the Sonicmodell Skyhunter 1800. ...I've designed it to fit over a RMRC 800mw VTX.

The Micro Skyhunter motor mount is a perfect fit for typical quadcopter motors with 16 and 19mm hole separations. ...It's specifically designed to work seamlessly with popular motors like the Emax RS2205 and Cobra 2204.

example of one of the design options https://youtu.be/j8P4fEPCAMo Donate Payoneer --- alexzn64@gmail.com All files --- https://www.cgtrader.com/3d-print-models/hobby-diy/robotics/bunker-for-skyhunter-1800-trichogramma The Skyhunter 1800 EPO aircraft...

... and acquaintance only! Updated version, All source models and files are on this site https://www.cgtrader.com/3d-print-models/hobby-diy/other/motor-mount-for-skyhunter-1800 There I am attaching STL and source files for changes for your engine. ...

A compact pan-tilt system specifically engineered for the SonicModell mini Skyhunter drone. ...This custom-designed assembly seamlessly integrates a Runcam Split 3 micro camera module alongside two high-performance TowerPro MG90S servos, ensuring...

The mini skyhunter cockpit boasts an impressive 1238mm wingspan, far from a diminutive design. ...This ingenious camera mount is tailored for use with a versatile tool, available at https://www.thingiverse.com/thing:1110726, which seamlessly integrates...

A precision-crafted flight control mount for the compact Skyhunter mini drone. Engineered to securely accommodate the Matek F722 flight controller, alongside a Matek SAM-M8Q GPS module and a LittleBee Spring 40a ESC. Other similarly sized flight...

The Skyhunter 1800 EPO aircraft is used as a carrier for the introduction of substances in agriculture. Hopper - Max height 80mm, width 117mm, length 136mm Printed in its entirety. Serva Emax ES08. The flow is regulated by impulses of opening and...

I designed this part specifically for building the A-Tail on my Skyhunter, and I'm excited to see how it performs. Why did I decide to take on this project? Simply because I wanted to try something new. As of today (02/09/18), I haven't had a chance...

Skyhunter users can rely on the APM ULRS mount for capturing breathtaking astrophotography images with minimal equipment adjustments required. Its user-friendly interface and intuitive controls make it easy to navigate and configure settings for...

I created this part specifically for my Micro Skyhunter plane, to complement the front landing gear I designed earlier (https://www.thingiverse.com/thing:2764934). To assemble it, simply insert the wing bolts through the sliders before attaching...

This is a work in progress main gear set for the RMRC 1.8M Skyhunter. 1/1/2020 Update - Main gear holes are now large enough to accommodate M3 hardware, and larger holes have been created for Dubro stub axles. 1/8/2020 Update - V2 STL has been...