nano talon evo 3d models
14259 3d models found related to nano talon evo.thingiverse
Nano Talon EVO comes with bigger battery section thanks to much lowered battery plate. This is my mod for original Nano Talon to achieve similar battery compartment capacity. Printed in PLA, 3;3;3 layer settings with 0,4 nozzle and 10% infill. ...
thingiverse
Camera protector for Nano talon / EVO Battery protection. ...In the event of an accident, the battery will rest against the protection and will not break the camera
thingiverse
Is for the Nano Talon Evo to mount the Runcam Hybrid Board lil bit safely on the plane ;-) print like u want ;-)
thingiverse
Tail cover for the Nano Talon Evo (may fit Nano Talon but haven't tested this). I made this after the tail of mine was broken on a hard landing. Adds rigidity and offers more protection than the stock plastic piece. ... I used hot glue to hold it...
thingiverse
Replacement nose hatch for the ZOHD Nano Talon EVO. Printed using eSun PLA-LW on an Ender 3 with direct drive extrusion. The included gcode file will work with any Ender 3 with a 0.4 mm nozzle. Use CA glue to attach the thumb screw. This...
thingiverse
A simple air vent for the ZOHD Nano Talon Evo rear hatch, Easy to print and fit. ...It increases the air intake to help cool the electronics inside.
thingiverse
Zohd Nano Talon Evo rear servo bay fuselage brace Slots and glues in to the rear bay to stiffen the fuselage, to prevent torque twist.
thingiverse
... of the Nano Talon. ...Requires 2 M3 x8mm screws and appropriate nuts, as well as the 4 screws which come with the Nano Talon's mount. I used some washers under the front screws, to level it out. ...This will depend on the curve of your canopy.
thingiverse
Nano Talon EVO Cargo Door for Go Pro Hero 3. Prints 23 grams at 2% infill with carbon filled pla with 2 outlines. Rev 2 - Updated to include more accurate magnet position, better access to buttons, and added protection for lens. ... Comes at a...
thingiverse
I wanted a clean way to mount the VTX and Antenna on my Nano Talon Evo. These parts mount to the underside of the nose/canopy lid and are out of the way of the battery etc. You'll need to cut a 17mm hole in the lid for the antenna mount. The...
thingiverse
This mount is designed to allow the DJI Digital FPV system Air Unit to be mounted under the front hatch of the ZOHD Nano Talon Evo. It is intended to sit under/behind the naca duct and provide some space for good airflow to cool the Air Unit. I...
prusaprinters
This mount is designed to allow the DJI Digital FPV system Air Unit to be mounted under the front hatch of the ZOHD Nano Talon Evo. It is intended to sit under/behind the naca duct and provide some space for good airflow to cool the Air Unit. I...
prusaprinters
I wanted a clean way to mount the VTX and Antenna on my Nano Talon Evo. These parts mount to the underside of the nose/canopy lid and are out of the way of the battery etc. You'll need to cut a 17mm hole in the lid for the antenna mount. The...
prusaprinters
<p>The parts were printed with PETg and the sideplates were fixed with double sided tape to the fuselage.</p><p>The antennas lays flat against the foam of the fuselage and they are not able move in flight.</p><p>The hatch closes without cutting any...
thingiverse
The Nano Talon EVO used to come with a balsa mount for a downward facing GoPro/Action cam, but it seems to be sold separately for $20 nowadays. This model should do roughly the same thing in the same way. The dimensions here are based on the Akaso...
thingiverse
About *** This is a motor mount replacement for ZOHD Nano Talon EVO. I designed this to be robust and to allow replacement whenever the mount breaks or gets damaged. Hardware *** You need: * 1 x M3 5x5 mm threaded insert * 1 x M3 x 20 mm screw...
thingiverse
... Rebel DJI FPV Airunit Mount. ... Print with Naca intake on buildplate, no support needed. Melt in 3mm threaded inserts with soldering iron. use DJI_FPV_Air_Unit_Nano_Talon_Bracket from design DJI FPV System Air Unit Mount for Nano Talon Evo by Mrj666
thingiverse
This is a replacement clip for the ZOHD Nano Talon wing. ...It was created with Sketchup
thingiverse
This is a USB socket to be use with flight controllers (like iNav ones) for the Nano Talon.
thingiverse
Holder for VTX for ZOHD Nano Talon to be used on a nose canopy.Fits AKK X2-Ultimate but should fit also other VTXes
thingiverse
Just a really simple wall mount for the Nano Talon - I wanted to hang it on the wall, just print two of these and then it will hang by the wings.
thingiverse
This is a work in progress. ...After several accidents I decided to design a nose cover for my Nano Talon. ...The idea is not only replace the original, I would like to incorporate some mods to it.
thingiverse
For Nano Goblin mod. ...Place servos on wing. v3 is thin, v4 is more robust. Some more details (plenty of photos) on our French forum: http://www.france-fpv.fr/viewtopic.php?f=15&t=1117&hilit=nano+talon&start=220