nanotech 4s lipo 3d models
12542 3d models found related to nanotech 4s lipo.thingiverse
Fits for 1300mah 4s Turnigy nano tech and 20mm battery strap. Fits for 1550mah 4s SLS and 20mm battery strap. ...Print Settings Printer: Mendel90 ...
grabcad
A simple model of the Nanotech 1800mAh LIPO 11.1v found on HobbyKing
thingiverse
Immediate insight into your LiPo battery status. Wiring towards "Full", the battery is full. Wiring towards "Empty", the battery is empty. ... Length = 31 mm Width = 28 mm CaseHeight = 37mm Designed for "Perimeters only" printing.
thingiverse
Case to store 5x Turnigy Nanotech 2S 300mah 45-90c lipos.
thingiverse
16mm battery mount for micro quads. ...Made for Nanotech 2S 300mah lipos. ...Print in tpu so it will fit 15/16mm mounting.
thingiverse
I didn't want my soft wrapped NanoTech LiPo bouncing about inside my OpenRC F1 car and i wanted it to be a bit safer for transport so i designed this fits inside the OpenRC F1 Electronics Holder designed by Noneus...
thingiverse
Simple 4s Lipo Desk storage container. ... Measurements are for a Goldbat 4s 1300mah lipo.
thingiverse
This protector is for 4s Lipo 1300mah. ...Print Settings Printer: néo 1 Infill: 20%
thingiverse
For mounting a 4s lipo under the drone. LipoTop on top of the Lipo and LipoBottom under. ...Strap the package with a Lipo-strap under the drone.
thingiverse
4s Lipo Battery Protection for your drone. Strap slots are sized for 16mm straps. ... There are two versions, one for square packs, and one for long traditional packs.
thingiverse
... not damage your battery in case of a fall. ... It is designed for AXTech Infinity Grapheno 1800mA 4S LIPOS. The opening below is for passing the battery strap and securing it together. ... Prefer to print it on TPU for best results and protector.
thingiverse
... not damage your battery in case of a fall. ... It is designed for AXTech Infinity Grapheno 1500mA 4S LIPOS. The opening below is for passing the battery strap and securing it together. ... Prefer to print it on TPU for best results and protector.
grabcad
... Discharge Rate: 25 C, Plug XT60 Plug4S1P lipo batteries size: -4.17 x 1.38 x 1.34 inches (L x W x H); approx. ...weight: 232gApplication - Sunpadow 2250 mAh 14.8 V 4S Lipo battery suitable for RC FPV helicopter airplane quadcopter drone racing model.
thingiverse
It´s a LiPo-mount for the green Multistar 4s 5200 LiPo. Customized version of http://www.thingiverse.com/thing:348618 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=348618 ...
thingiverse
Bonjour, Voici des protections pour lipo 4S 600 mAh et 1500 mAh sur mesure avec plusieurs détails pratiques pour l'utilisation. ... - Taille adapté pour les drone racer 3 pouces - Protège tous le tour - Compartiment pour glisser la sangle de sérrage ...
thingiverse
Lipo Protection for lipos that measure 50mm x 55mm, such as the Black Label square packs from Indescructible Drones. ... Slots on side fit 16mm straps.
thingiverse
Lipo case for Planes to fix the battery allways on the same perfect Location
thingiverse
This is a lipo balance lead strap. It keeps your balance lead from ending up in your props during a crash. ...Should fit most 4 cell packs.
thingiverse
Just a simple box model for a S4 5000MAh LiPo battery. There is some room left on the side to make sure the battery can expand. You could place a little bit of foam on the inside to stop the battery from moving (though straps do the same). On V2...
thingiverse
Protector de lipo para multistar 4s 4000mah. ... Logo de AKframes.