nema 11 planetary gear box parametric stackable 3d models

Thingiverse.com/Apps/Customizer/Run?Thing_id=1561008 Instructions Using the Following Options: Box Separator Number Length = 2 Separator Thickness = 2 Lid = Yes Box Label Movement Left Right = 6 Box Separator Number Width = 3 Box Separators Over...

A little remix of the modular resistor stoge box (3125601)

http://www.thingiverse.com/apps/customizer/run?thing_id=1561008 Instructions Using the following settings: box separators go beyond length no box separator numbers have two digits long boxes are 150 units in size box labels are blank box labels move...

A small, compact, modular box storage system based on Adafruit's Snap Fit Box found here: www.youtube.com/watch?v=VVmOtM60VWw

Diese Stapelbare Box kann zum Lagern von Langen Gegenständen genutzt werden.

I made a remix of this box so it can hold name tags. ...Nametag size ~ 60x20mm

Configure the design with these parameters: * stack guide length: 6 units * box width: 100 units * front side wall ratio: .40 * box depth: 100 units * thickness: 2 units * box height: 70 units * stack guide width ratio: 3.5 units * front face...

I wanted Box hold everyThing for my screws and some small electronics so i came with this design 1 - easy to print 2 - Fully customizable 3 - Compact 4 - Solid 5 - No need extra Hardwares Filament / some screws update 22/09/2021 added 1/2 box to 1:1...

... for maximum storage. ...This large box has width and length dimensions of 6 inches x 6 inches. the height of the box is 70 mm. each box also has a place where a label can be attached so that the contents of each box can be identified quickly.

Options Used: stack_guide_fn (Guide Notch Size) - 6 angle (Cut Angle) - 60 degrees box_width (Main Box Width) - 150 units front_thick (Front Wall Thickness) - 8 units thick (Wall Thickness) - 3 units box_depth (Main Box Depth) - 250 units...

Instructions Using the following parameters: box_depth = 200 front_thick = 10 angle = 75 front_side_wall_length_ratio = .50 box_height = 85 thick = 2.5 stack_guide_width_ratio = 4 stack_guide_fn = 8

Multiple stages can be connected as needed, allowing for an almost limitless potential in gear combinations. The model also features a crank handle that can be printed directly into place. The required bearings are 21 OD x 12 ID x 5 wide, and one is...

Custom Options These are the choices you've made to personalize this design: Stack guide width ratio: 3.5 units Stack guide function number: six Box width: Eighty-five millimeters Box height: Seventy millimeters Angle of box: Forty degrees Wall...

The box stands alone, yet many printed copies of it can be stacked on top of one another.

Instructions: Using the following parameters: * Box width: Sixty Units * Front panel thickness: Eight Millimeters * Front and side wall length ratio: Point Four Oh * Angle: Sixty Degrees * Box height: Forty Units * Stack guide function value: Six *...

Instructions Using the Following Settings: Box Height - Set to 45 Stack Guide Width Ratio - Optimized to 1.5 Front Side Wall Thickness - Boosted to 2.5 mm Box Dimensions - Box width set to 80 , box depth to 110 Stack Guide Functionality - Activated...

This is a free (GPL) customizable box designed using OpenSCAD, and you can modify everything simply by editing a few values, including the box size, lid text, and layout of the box itself. I utilized this fantastic OpenSCAD library to add text to the...

http://www.thingiverse.com/apps/customizer/run?thing_id=307059 Instructions Using the following options: box_depth = 150 angle = 60 front_thick = 3 box_width = 100 box_height = 60 front_side_wall_length_ratio = 0.6 stack_guide_width_ratio = 3.5...

http://www.thingiverse.com/apps/customizer/run?thing_id=307059 Instructions Using the following options: angle = 40 front_side_wall_length_ratio = .40 box_height = 35 stack_guide_width_ratio = 3.5 thick = 2 front_thick = 8 stack_guide_fn = 6...

... stack boxes. Choose to have them with or without partitions. Two flat containers side by side create precisely the height of a high-rise box. A rectangular design keeps boxes aligned correctly. ...Very sturdy despite minimal use of materials.

Instructions: Utilizing the Following Options: - Front Thick: Set to 8 - Stack Guide Width Ratio: Altered to 3.5 - Front Side Wall Length Ratio: Configured at .40 - Thickness: Determined as .5 - Box Depth: Calculated as 70 - Box Width: Specified as...

http://www.thingiverse.com/apps/customizer/run?thing_id=307059 Instructions Using the following options: box_height = 35 thick = 2 stack_guide_fn = 6 angle = 65 front_side_wall_length_ratio = .75 stack_guide_width_ratio = 3.5 box_width = 50...

Hello everybody, this is my solution of a screw box to organize screws and nuts or something like that. The box has a gap to avoid slipping over. Also there is a hook to hang the boxes on the wall without having to stack them. ...

... with Customizer! ... Instructions Using the Following Options: Box Width = 60 Front Side Wall Length Ratio = .4 Stack Guide Function = 6 Front Thickness = 8 Inner Thickness = 2 Box Depth = 70 Stack Guide Width Ratio = 3.5 Angle = 40 Box Height = 80

Instructions To Use: Select from Options Set Box Height: 35 Set Thickness: 1.5 Adjust Angle: 50 Customize Front Side Wall Ratio: 0.50 Define Stack Guide Function: 6 Choose Box Depth: 70 Determine Stack Guide Width Ratio: 3.5 Pick Box Width: 50...

It was created using the Customizer tool with specific settings including a box depth of 125, front thickness of 4, an angle of 45, stack guide function set to 5, stack guide width ratio at 5, and a front side wall length ratio of .7. ...The box height...

Instructions Utilizing the Following Settings: Stack Guide Width Ratio Set at 3.5 Units Box Depth Established at 90mm Measurements Box Height Fixed at 35mm Specifications Stack Guide Function Designated as Version 6 Front Side Wall Length Proportion...

Instructions You'll Need to Follow These Steps: Choose the Settings You Want: front_side_wall_length_ratio = 0.40, box_height = 80 mm, box_depth = 50 mm, front_thick = 8 mm, angle = 40 degrees, stack_guide_fn = 6 mm, box_width = 60 mm, thick = 2 mm,...

Designed Specifically from http://www.thingiverse.com/thing:307059 Using Customizer Tool - Try It Here http://www.thingiverse.com/apps/customizer/run?thing_id=307059 Options Selected Below box_width = 100 Front Side Wall Length Ratio = 0.4 stack...

The printer effortlessly prints the box directly onto the build plate, as illustrated in the accompanying photograph which clearly shows the backplane in position.