nema 17 stepper motor for 3d printer

I had been wanting to clean up the cables on my Ender 3 Pro so I decided to make a simple cable routing support that mounts to the NEMA 17 extruder stepper motor.For the MicroSwiss direct drive setup, the stepper needs to be removed to slip the lower...

I've taken this Belt tensioner, specifically mounting it onto a Nema 17 Stepper Motor through means of M3 Screws. ...When it comes to tension hardware, I employed not one but two eight-millimeter bearings paired alongside a one-fourth twenty-inch Bolt...

This is the shorter Nema 17 stepper motor with 6 wire connector. ...Usually only connected with four wires going to a 6 pin connector.Body Length: 39.5mmTotal Length: 55.5mmWidth: 42.2mmShaft: 5mm diameter

Enclosure for Minebea 17PM-K374BN01CN 38mm NEMA 17 stepper motor, currently sold by Pollin for less than 5 3 €. The 45x45x45mm case makes the stepper motor compatible with the fischertechnik construction toy system. It might also fit for other NEMA...

NEMA 17 Stepper Motor: 28, 34, 40, 48, 60 mmAdjusting the motor's height is easily done in Fusion360 by selecting "MODIFY" and then choosing "CHANGE PARAMETERS" from the dropdown menu. ...The height of the motor can be adjusted to 40mm with just a few...

Nema 17 Stepper Motor 17HD48002H-22BSpecifications: Shaft diameter: 5mm Shaft length: 20mm Motor body length: 48mm Full length: 70mm Weight: 380g Step Angle: 1.8° Step Accuracy: 5% Holding Torque: 0.59N·m (84oz·in) Rated Current/phase: 1.7 A Phase...

Previous version (version 3) preserved for reference (images located at the end of the gallery).\r\n\r\nHousing for [Minebea 17PM-K374BN01CN 38mm](https://www.eminebea.com/en/product/rotary/steppingmotor/hybrid/standard/17pm-k.shtml) NEMA 17 stepper...

This is a NEMA 17 stepper motor mount designed for use on an optical breadboard, ideal for experiments and prototyping purposes. The distance between mounting slots is carefully set at 2 inches to accommodate optical breadboards with 1 inch hole...

A shaftless Nema 17 motor was purchased on eBay from the seller PacificBearing, featuring a 5mm bore.

The NEMA 17 used in this assembly was originally sourced from pefozzy on Thingiverse and combined into a single part for generating BOMs of various projects (thing:185269 and thing:456025). ...The heatsink was obtained from Alan Bullick's aluminum...

A Nema 17 motor with 45 oz-in of torque is featured in the listings provided by StepperOnline, an eBay vendor.

From the original (see remix-link), I resized the Top part a little to fit the Stepper Motors 17HS19-2004S2 I've got from...

model motor stepper to design mechanical

I designed this thing to cool the z motor on my cnc, but it can be used on any NEMA-17 motor with enough clearance around the sides and back. It uses a 40mm fan. The square duct cross section measures 55mm along the vertexes. The duct protrudes ~15mm...

I designed this thing to cool the z motor on my cnc, but it can be used on any NEMA-17 motor with enough clearance around the sides and back. It uses a 40mm fan. The square duct cross section measures 55mm along the vertexes. The duct protrudes...

Works with motors up to 40mm in height and have the nema 17 standart. M3x8 screws work great with the motor, and for the mount iself the holes are for M3 screws. Wall line count should be high since they will endure the pressure of the screws I...

A Nema 17 color scheme is available from the ebay seller, StepperOnline.

Stepper motor that was used on the RepRap Mendel/Prusa Mendel.

Works with motors up to 40mm in height and have the nema 17 standart.Wall line count should be high since they will endure the pressure of the screws I used 7 but 5 should be enough.Print with legs straight up not on it's side(like the one in the 3rd...

I'm looking for a model of my stepper motors for the extruder that I'm eager to experiment with. And yes, the actual stepper motor doesn't have a flat on the shaft either. I'll need to mill them myself. I've included the source file in STEP format...

This is a straightforward modification to space the stepper motor correctly for the pulleys of the small X,Y belts on an Ultimaker (revised UMO+). The belts were consistently rubbing against the plywood and there was no way to properly align them...

MOTOR LENGTH 34 MMMotor length: 34mmDiameter of axle: 5mmVoltage: 12VThe front shaft length: 24mmSize: 42mm * 42mm * 34mmHolding Torque: 2.8kg.cm Scope: 3D Printers, Monitor Equipment, Medical Machinery, Textile Machinery, Packaging Machinery, Stage...

Attached is the step file for my rendition of the NEMA17 Pancake Motor found on the Bondtech LGX

Attached is the step file for my rendition of the NEMA17 Pancake Motor found on the Bondtech LGX

I designed this thing because my motors have fixed wires, and I like to have terminal blocks for all the wiring. ... I had a bunch of that black terminal strips, with a 8 mm pitch, so I cut them in groups of 4 connectors, that fit tight in the support.

I built this device because my motors feature fixed wires, and I prefer having terminal blocks for all the wiring. ... I used up several pieces of that black terminal strip material with an 8 mm pitch spacing, cutting them into groups of four connectors...

I used Prusa-slicer to alter the original design by NotLikeALeafOnTheWind. ...I needed something that I could actually hold onto to stall the motor easily. ...Quick Print under 10 minutes.

Manufactured purely for evaluation purposes.

... ...With its 10 multi-colored Neil's NeoPixel smart RGB LED lights, you can create dazzling visual displays. Plus, its capacitive touch sensor allows for intuitive control without any additional components. ...Order now and unleash your creativity!

My goal was to create a converter for the possibility of using force from Nema 23 motors because I want to utilize a 0.9deg stepper motor (the most precise dosage of filament) with Bondtech extruder. This applies especially to capricorn tubes with...