nema 6 50p plug 3d models
413807 3d models found related to nema 6 50p plug.grabcad
Modeled the plug end of my 40 amp 6-50 heavy duty extension cord with 3-8 awg conductors.Model units are inch.
youmagine
A common welder plug is a NEMA 6-50 plug. ... This cover can protect your male plug from debris or moisture.
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
This is a plug cover designed to fit the NEMA 14 style of plugs (14-30, 14-50, 14-60) Print Settings Printer: XYZ DaVinci 1.0 Rafts: No Supports: No Resolution: 400 Microns Infill: 10%
thingiverse
Fits the NEMA 5-15P socket from Tronxy X3a power supply. ...Screw the plug to the case with two m3 screws. Attach to plug to enclosure using 4 m4 screws. ... The threaded portion at the top fits a 1/2 NPT strain reducer.
grabcad
NEMA 5-15P PART NO: HBL5266C2-Pole 3- Wire Grounding, 15A, 125V, 5-15P, Black and White
thingiverse
This is a full remake of a design form another member but I have changed it up for a NEMA 24. I will edit and link the other site when i find it again. Enjoy. ... remake from https://www.thingiverse.com/thing:2832630 I'm not sure if that's how i...
thingiverse
A Nema 23 Stepper Motorcap. With Superseal 4pol. ...Plug
thingiverse
This is a plug cover for 30 amp travel trailer style plugs (NEMA TT-30). ...Print Settings Printer: XYZ DaVinci 1.0 Rafts: ...
grabcad
Plastic cover for NEMA 23 step motors with the GX16-4P aviation plug.Two models are available with the two positions of the plugs.Covers are 3D printable and if someone find it useful please print one and share with us.
thingiverse
This is a simple coin holder for the special edition Peter Rabbit 50p coins I've placed the year in the top right, as there are coins from 2016, 17 and 18, but obviously you can remove or change that as you like. ...
thingiverse
Nema 23 stepper rear cover with db9 female plug and 50mm cooling fan holder. Instructions: Cut the stepper cable with approximately 100 mm, pass the wires through the inside of the case and weld them to the db9 plug. Also connect the two fan wires...
thingiverse
A cap to protect the pins on a NEMA L14-30 locking plug. This kind of plug is commonly used on emergency generator cables. (or, in my case, a charging cable for my Volt!) I designed this because these cables and plugs spend a lot of time in storage...
grabcad
The aviation plug is then fixed for the "top" part and the stepper connector wires are soldered for the aviation plug pins. Then the "top" part is fixed to the "bottom" part by screws and nuts.I made it just like the possible solution for the...
thingiverse
... collection of UK 50 Pence coins. ...Each plaque holds 7x 50p coins with the stand holding 7 plaques in total (49 Coins). The plaques hold a 50p in place with out any glue, although your print may need some tweaking depending on your printer/settings.
prusaprinters
The plaques hold a 50p in place with out any glue, although your print may need some tweaking depending on your printer/settings. Print instructionsCategory: Coins & Badges Summary This is a stand for my collection of UK 50 Pence coins. Each...
thingiverse
This is a homage to the brutalist masterpiece that is the '50p building' in Croydon, also known as the NLA tower, threepenny bit building, wedding cake and now Number 1 Croydon. https://en.wikipedia.org/wiki/No._1_Croydon Made up of a series...
prusaprinters
This is a homage to the brutalist masterpiece that is the '50p building' in Croydon, also known as the NLA tower, threepenny bit building, wedding cake and now Number 1 Croydon. https://en.wikipedia.org/wiki/No.\_1\_Croydon Made up of a series of...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=299663 Instructions Using the following options: outer_diameter = 25 opening_width = 2 pressure_point_thickness = 4.5 nut_diameter = 8.5 diameter_top = 6.35 height = 30 articulation_thickness =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=299663 Instructions Using the following options: outer_diameter = 30 opening_width = 2 pressure_point_thickness = 4.5 nut_diameter = 8.5 diameter_top = 6.35 height = 30 articulation_thickness =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: no_of_nuts = 1 retainer = 1 pulley_t_ht = 8 m3_dia = 3.2 pulley_b_dia = 20 nut_shaft_distance = 1.2 additional_tooth_width = 0.2 teeth = 20...
thingiverse
NEMA 5-15 (Three Prong) Plug Protector with Strap for Heavy Duty Power Tool cords. ...This is a remix of the fuchsr design.