nema17 stepper 3d models

Black Nema17 Stepper Motor 42 x 42

Model of a nema17 stepper motor

Diferrent sizes of NEMA17 stepper motor

Nema17 Bipolar Stepper Motor42x42x50mm45Ncm

A NEMA17 stepper motor mock-up with a rotating shaft and face mounting capabilities. ...

NEMA17 stepper motor made for prototyping of Prusa i3 / grabber style of 3D printers http://reprapworld.com/?products_details&products_id=94&cPath=1614

5mm thickness, 8.5mm bore, NEMA17 stepper. ...I built this to use a thrust bearing on my Prusa Air 2 paired with this: http://www.thingiverse.com/thing:16663

This is a stepper extruder mount that I whipped up in Sketchup designed to mount a NEMA17 stepper motor on a Brutstruder (http://www.thingiverse.com/thing:4036). This is currently untested, though it will theoretically fit. You'll probably want to go...

The original design for the NEMA17 stepper motor mount is from ccox in Thingiverse. Here is his Thingiverse link:https://www.thingiverse.com/thing:2073446 

Do you have a NEMA17 stepper mounted on a flat surface? This will be the thing you need to improve the overall fixture and reduce the vibration. Instructions 1) Print 2) File the center hole if it...

I've ordered some NEMA17 stepper motors from a Chinese supplier. I haven't received them yet but in order to do the design in advance, I had to make this part with rough dimensions from the product listing page. When I get the actual steppers, I am...

These are some dampers for nema17 stepper motors. I printed these in soft PLA but other flex filament probably work too. Apply z-scaling if they are too soft or too hard. (I used 20% infill). Goes well together with my printer coasters:...

A NEMA17 stepper motor mock-up with a rotating shaft and face mounting capabilities. Print Settings Printer: Prusa i3 MK2 Dolly Rafts: NoSupports: Yes Resolution: 0.2Infill: 10% Post-Printing Remove supports and clean up. Assemble according to...

A plastic piece to mount onto a NEMA17 stepper motor. ...You can lock the cable to it using a zip tie to remove stress on the connector.

All the NEMA17 mounts I found were too flimsy - I increased the thickness and gusset size as an improvement

Nema17 90 degree motor mount. Holes are on 20mm center to work with 20mm aluminium extrusion. ...holes are 5.1mm to work with m5 bolts.

Dimension accurate models of one of the most common stepper motors for Fusion 360 users.

Useful for making a stepper motor general purpose. ... Instructions Print the two parts Screw the motor on with four screws Clamp it on a rod with four screws and nuts Design and print something to make...

To be printed in PETG, ABS or another high-temp material (the stepper could become hot). Spacer for X and Y axis. Used SolidWorks 2019 SE. Uploaded STEP file as well. ... Size: outer box 52.3mm x 42.3mm x 16mm Screw holes: ID 3.5mm, OD 7.5mm, center...

A part of an interactive installation called Spinoxa which you can find on http://www.tadaex.com/2016/artists/ashkan-gh/ the mount was screwed to the wood frame Stepper...

Since I'm replacing the Z axis in my Replicator clone with a threaded rod that's 3cm too long, I needed to lower the NEMA 17 stepper motor bolted to the bottom of the printer. This is a spacer to accomplish just that. Adds about 3.5cm of spacing (it...

Fully adjustable motor position for belt tensioning via loosening of stepper mounting screws. Clocking is also adjustable by turning the mounting plate to desired position. Installation requires cutting a 3" hole (by means of 3" hole saw in base...

This is a bracket that perches on a 3/4-inch plywood board and holds two NEMA 17 stepper motors side by side. I designed this for use on a drawbot I'm building - I decided to center the motors to simplify wiring. I'll just place two pulleys at the...

Nema17 stepper motor holder.Configurations available with M6,M5,M4 bolts.Nema17 bolts are M3.

... in Decelerating device. so i decide to make my Decelerating device with 3d printer. ---it is my first project. < parts to need>:: 1. M3x12==>10 2.M5x12==>3 3.M3 nut==>6 4.M5 nut==>3 5.Nema17 stepper motor https://youtu.be/RdPcIRQUpnc

Nema17 stepper motor mount with cut-out for wiring. Suits 23mm height motors. *I will uploaded other sizes if there is enough interest * If you don't need the cut-out simply print 2 x of the solid mounts. ... Gives more space for the motor to vent...

Nema17 stepper motor mount with cut-out for wiring. Suits 23mm height motors. **I will uploaded other sizes if there is enough interest ** If you don't need the cut-out simply print 2 x of the solid mounts. ... Gives more space for the motor to...

Vibration dampers for NEMA17 stepper motors =================================== Install these between your X and Y stepper motors and the motor brackets to reduce noise and vibrations. There are other dampers on Thingiverse, but none, that I could...

... 3 nuts. - 1* 5mm hexagon socket head screw 30mm long (but trimmed down) and 3 nuts (small height). - 2* 3mm hexgon socket head screw 40mm long with 2 washers. - NEMA17 stepper driver (5mm diameter axis)..- MK8 drivegear for 5mm axis.

Adapter for mounting a geared NEMA17 stepper motor to a standard NEMA17 stepper mounting bracket. Specifically, I designed this to mount a Zyltech 17HD48002H-C5.18 to a NEMA17 adapter like this (no affiliation) using four M3x5mm socket head cap...