neptune 3 plus 3d models

When trying to make or customize hot end holders, fan holders, fan ducts for my Neptune 3, getting them to fit just right has sometimes been an issue. This is just the hole template for the carrier of the Neptune 3. It is not the same as an Ender 3...

Este archivo es un remix de un soporte para la pantalla de https://cults3d.com/en/3d-model/tool/support-d-ecran-deporte-pour-elegoo-neptune-3-proLo he modificado para poder cambiar de posicion la pantalla en la impresora.

The filament spool holder for Elegoo Neptune 3 Pro can be installed on both sides of the bracket. There is only one included in the set. ...This product will allow you to install two filament spools at once.

Modified the original holder to reduce wobble on the main platform by adding a support strut and removing part of the original base that was redundant for Neptune 3.

A simple adapter to use Filler with the existing filament holder of the Elegoo Neptune 3. ...It simply slots into the end where you would normaly screw the factory roller in.

This is a shorter Endstop for the elegoo neptune 3, since i noticed it was stopping very far away from my bed and was taking too much time. ...So I designed this one to be shorter.

This is a shorter Endstop for the elegoo neptune 3, since i noticed it was stopping very far away from my bed and was taking too much time. ...So I designed this one to be shorter.

Elegoo Neptune Z Axis Stabilizer for better Printing

Remix of Elegoo Neptune M4 Extruder Mount that fits https://www.printables.com/model/259303-elegoo-neptune-m4-extruder-mount

The original holders were made for an Ender 3 Pro and unfortunately they don't fit the Neptune 3 so I made a small adjustment so that it fits. ... NOTE: This part is specifically made for this LED Bar: ...

Also see my LED difusor remix for Neptune 3 pro https://www.printables.com/cs/model/665424-elegoo-neptune-3-pro-light-bar-slim-diffuserZ mount is made from 2 pieces GLUE them togetheraround 36 chains will be needed around 42 clips will be neededother...

The design idea was taken from Pickle_Rick_1, but it was drawn from scratch in Autodesk Inventor, especially for the Eleego Neptune 3 printer. The holder is attached with 3 screws of the power supply. ... I use this scrapper - Astra Razor Blade...

This is a display stand for the Elegoo Neptune 3 series. The original display stand only fits on the right side of the printer. This one fits on the left side. ... ( i am quite sure it will fit on any 40mm aluminum profile ) extra's : 2 magnets,...

The part was designed in Tinkercad.I wasnt able to find any model to replace a broken pad support for Neptune 3 max, so I designed it from scratch.I have reinforced a few things to avoid future problems.The part has the measures to fit the magnet...

This is a simple glue stick holder that attaches to the side of your Neptune 3 Pro. ...I made this by using the clamp geometry from the remix file, making it slightly sharper, and building the rest of the model around the stock glue stick that came with...

This is for those of you who want to use the satsana style fan blower with the Neptune 3, but still want a more original look. ...The fit for this is pretty good, but longer screws would be beneficial as it does not go deep into the satsana screw holes.

Parts Needed:NF-B9 redux-1600 PWM (or any 92x92x25mm fan)4 x 4mm fan screws (included with the fan)1 or 2 M3 screws and nuts (for securing the LM2596)LM2596 DC-DC Buck Converter Step Down ModuleDC 12V PWM Speed Controller (4 Wire) for PC fanThis...

A simple side webcam mount that can be installed on the front left corner of the Elegoo Neptune 3, by removing the end cap and sliding into the profile rails. Designed to be compatible with webcams that have a 1/4" mounting screw (can be printed...

Had an issue on my Elegoo Neptune 3 where I had a print stop printing and the heat bed jumped super high. Dont know why it happened but It ended up melting the my heat bed spacers. ...I ended up making some replacement spacers for it.

Elegoo Neptune 3 Fan Duct with Silencer. Silencer - remix of this project: https://www.thingiverse.com/thing:3597687 Turbines mount without screws. I use e3dV6 heat block and nozzle, but I think it will be work and with CR10 heat block. ...

This is snap-in Elegoo Neptune 3/4 Filament Sensor Mount making much better tension on the filament solve the crogging or sponging effects.This works w/ or w/o stock spool holder also you DO NOT need any additional bolt or insert nut for the...

This uses the stock 4010 fans on Neptune 3 Max No bolts to hold as it's nice and tight, just push in the fans after attaching to extruder. Furthest edge from nozzle can be pushed in all the way until it stops , then carefully push & level out the...

with sufficient infill if you don't trust your filament ;D--------------------------------------------------------------------------------------------------------------Additional Spool Holder for the Elegoo Neptune 3 Pro with great fit direct after...

I have my Neptune 3 Max sideways against a wall and was tired of going around to look at the screen to operate or check progress. This mount uses the 3 factory holes and same screws to the printer frame. All that's needed is (2) #6 x 1/2" long sheet...

Fitment for Neptune 3.This is an upgraded fan shroud for the Neptune 3 platform to add dual 5015 blower fans. Each blower fan utilizes its own duct and exit as pictured in the cutaways. Fans simply slide onto their slot and get secured with 2 screws...

You may have to open them slightly with a 3.2mm drill.Don't forget the T nuts :)If you plan on using the support bearings that come with the Dual Z kit, I have adapters for those here: Elegoo Neptune 3 Creality Dual Z axis support bearing mounting...

Держатель для датчика обрыва филамента для ELEGOO Neptune 3 PRO Все размеры и отверстия рассчитаны для беспрепятственного прочного зкареплеия на месте штатного держателя филамента с использованием заводского крепежа. Цель проекта - снижение...

Made a flat cable clip for the Elegoo Neptune 3 Pro. This is only for aesthetic reasons, I didn't like the OEM one as it squished the nice flat cable. Print it on its side like in the preview. ...Infill doesn't matter as it is made from perimeters,...

Just a really simple camera shelf or mount for the Elegoo Neptune 3 Pro. it just slides onto the plastic bracket for the touchscreen display. On this you can place a Pi Zero W with an attached camera. There are 2 versions: a solid one and a...

Modeled in FreeCAD (Open Source forever!).Holds the following tools: (round measurements given in diameter) Screwdriver (4mm shaft, 11mm handle cap)Screwdriver (2.5mm shaft, 10mm handle cap)Dual head wrench/spanner (25mm+ head, 20mm- head)Single head...