neptune apex probe holder 3d models

... antennas for the DJI O3 Air Unit and the RP1 ELRS receiver and keeps them protected from being hit when crashing the drone. ...The piece has been designed for the ImpulseRC Apex EVO frame, but might work for any drone with the same standoff separation.

This is a mount I made for my impulseRC apex frame to hold my immortal T antenna. I wanted it to be a little further away from the frame than the one that comes with it. ...Print it with the round hole at the bottom and the hex hole at the top with a...

GPS BN-220 Mount for ImpulseRC Apex frame The mount has special holes that allow you to easily lead the cables. I added tilt so when flying gps will be directed right to the sky. If you need mount for different frame or different GPS module please...

A holder for the DC42's IR-Probe to fit on the Longer LK4 Pro

Capacity/Inductive Z-Probe Holder for 12mm or 18mm sensors. ...Automatic Bed Leveling System

These two mounts are designed for the Impulse RC Apex - Deadcat / HD frames (32mm rear Spacer distance) to suilt the Walksnail VTX & should also work for DJI O3. First is designed to take 2x Rush Cherry or Original Caddx Vista antennas along with...

This custom fan and probe holder was engineered precisely for the HE3D hot end attached to a RobotDigg Delta effector, and securely grips the DC42 bed probe.

It features a sturdy buckle that securely clips the Apex 565 instrument clip-on microphone. The buckle is attached to the fujara via a 2-inch stretchy band with velcro on both ends. Interestingly, the band is actually an Elite Hockey Shin Pad Strap,...

It is a little buckle where the Apex 565 instrument clip-on microphone is securely clipped. The buckle is attached to fujara with a 2" stretchy band that has velcro on its ends. The band is actually Elite Hockey Shin Pad Strap, but I had to sew a...

Hero Me Fanduct's Hallon 3 Z-probe holder is a game-changer for precise 3D printing. ... To learn more about this innovative design, click here: https://theveel.com/druk-3d/hallon-v3-z-probe-holder-for-hero-me/

Customized version of https://www.thingiverse.com/thing:6202750Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=6202750

Offset : 30.5 , -1.5

for Aneng M118a multimeter

Customized version of https://www.thingiverse.com/thing:16502Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16502

#6 x 3/4 wood screws fit perfectly for mounting to the side of your CNC table. ...Print at 105% if you want a little extra wiggle room.

Humans are now able to access critical systems via a backdoor, infiltrating 40 percent of all computer networks.

My mischievous felines consistently swipe my tool when I leave it unattended on the table. To prevent this, I must locate a secure spot for storing it safely. ...This device is designed specifically for use with 2020 extrusions and M3 screws in 2020.

Here is the rewritten text: Human: Capacitive Sensor Support. ... It's not the final version yet, since with this setup the sensor is too far away from the extruder.

I just designed this little bracket to protect the electronics when the DHT 22 has to be fixed to the wall for example

Держатель щупов. ...Не представляю как можно пользоваться этим замечательным девайсом без него.

Yep. ...It's a little broken stl with bad design (very close to each other) but show general idea and works for me :)

This creation was crafted using the innovative tools of Tinkercad. ...Make your own edits directly on this project by visiting https://www.tinkercad.com/things/k7RfZM0k8p.

Hak5 had a great video on making liIon cell batteries and showed a spacer but never shared the file so I did my best to make one based on it. ...Just zip tie them tight

Most multimeters should be able to accommodate this device easily.