nerf 35 dart drum mag 3d models

... have been merged and reimagined: Thing #1257487, showcasing a practical dart holder, and Thing #2810780, featuring an ergonomic design concept. The result is a sleek and functional NERF Luger dart holder that combines the best of both worlds.

This is a better looking drum mag. I just modified the original design a bit. I think the "Adapter" is the same, but im not sure so im also posting the one im using. ... V3 can be found here: https://www.thingiverse.com/thing:6148807

Container to store Nerf MegaXL darts. Created in TinkerCAD. Hexagon relief to save on filament and time. ...Hexagons because “Hexagons are the bestagons” - CGP Grey</p>

This is a high-performance dart rail attachment designed specifically for use with Nerf Mega Blaster models. ... Units of measurement are provided in inches.

Hello there, this model, is a dart holder for the Nerf Tiger, from the Alpha Strike series. ... To adjust it to your blaster, I suggest you cable ties.

ALL FILES ARE ON MY PRINTABLES ACCOUNT AND WILL BE FROM HERE ON OUT https://www.printables.com/model/493375-n-akm-foam-dart-nerf-gun-blaster

I fashioned my own mounting solution for the Nerf Dart Tag Strikefire pistol since I couldn't locate any available scopes that fit its unique configuration.

This is a slide-in dart adaptor for a Nerf Arrowstorm. ...Has very thin walls in some sections, requires at most a 0.25mm nozzle to print.

This is a slide-in dart adaptor for a Nerf Arrowstorm. ...Has very thin walls in some sections, requires at most a 0.25mm nozzle to print.

A replacement dart tooth actuator piece for the Nerf Retaliator. This part has built-in supports, and is already in the optimal orientation. ...Enjoy!

Modified the energy cell from Hyena_Of_Doom so it could hold nerf darts including 2 half darts in each cell slot. ...Will be using this for a Nerf based Fallout LARP so wanted it to be functional to some degree.

Remove suction cup(s) from a Nerf dart (e.g., https://amzn.com/B00284C4FK) and clean off residual glue before attaching the dart head to the anchor and installing it on your caddy. ...Approximately 285mm of filament, costing about 5 cents, is required...

The Nerf N-Strike Jolt ships with two darts as standard issue gear. Unfortunately, your dart capacity is limited by design; you can only stow one in the barrel at any given time. To keep that extra dart secure and ready for action, a small plastic...

Nerf dart cutting jig to cut Elite size darts, up to 5 at a time, down to 36mm to be short darts. ... Designed to do 5 as it is to be used with my Hammershot so each set is a full reload.

This is a part to install in your Nerf MA40 or any blaster with an identical pusher head geometry, to allow it to shoot half darts. Couple points about that: This part is designed to work with the Worker Flywheel Talon Magazine Adapter. You will...

I've included the modified Spinning Nerf Dart Tip and the pointed version, along with the shaft and base as separate STL files so you can build or modify them for your own unique tip designs. ... I removed the suction tips from the original nerf darts...

this is the 1st part of my new project U5 to 12 short dart blaster kit this is the frist part of barrel to save the empty protection and fit short dart with at least 80fps use some tape to fix air for at least 120fps with workers short dart and i ll...

A replacement dart for the 2021 Nerf Sonic toys, such as the Dart-Launching Spoon. There are two versions, one using a standard Elite or similar dart head and the other being fully printable. The dart head version has a noticeable performance drop...

MP5 drum magazine M4adapterCompatible with Marui drum magazines2024/04/03Addition of fine-tuned products

This is a slide-in dart adaptor for a Nerf Arrowstorm. ...Has very thin walls in some sections, requires at most a 0.25mm nozzle to print.</p>

This is a custom-designed dart rail holder made specifically for Nerf Mega Blasters, and its versatile design allows it to accommodate various models, including the popular Tribreak gun. ...The measurements are provided in US standard units of inches.

This modification unlocks the full potential of Nerf Mega blasters by allowing them to fire Elite Darts instead of standard Mega darts. As a result, the firing range and power are significantly enhanced. To get the most out of this upgrade, use it...

This is a cutting-edge section designed to hold soft-tip projectiles like Nerf darts or similar foam darts securely within a versatile belt system. ...Various iterations exist, featuring a model without any stabilizing structures, another with...

I saw a nerf jolt silencer and scope and I was like wow I want this to hold darts so I made it hold darts. ... Print settings: just print it and use supports obviously Assembly: just look at the model that I remixed for the assembly instructions

... didn't have STL errors, so I designed one myself. ...This half-length dart cutter works great and is quick to use for Nerf blasters. ... The STL file units are in inches; you'll need to use math or Google to determine the scale factor for millimeters.

Here is a revised version with some creative phrasing: Jam-free zone: The Dart Retainer for the Nerf Rapidstrike glides smoothly into place, enabling you to use your jam door while containing rogue darts at bay. Tolerances can get tight; some...

Luckily, my Nerfs already had the Awesome Dart Holder for Nerf Gun by waltherion (10 clip) installed, so I decided to redesign the Nerf Sight to snap onto that instead. ...I printed mine in ABS with no supports and was pleased to find that it was a snug...

... of this storage box idea to keep the darts organized instead of all over the place. The Box was designed to fit darts with the following dimensions: Length: 2.75 inches / 7 cm Diameter: 0.5 inches / 1.3 cm (Designed using Elite Darts as Reference)

This is the Nerf Dart Launcher for the FPV-Rover (V1.0) http://www.thingiverse.com/thing:1240754 And for the FPV-Rover (V2.0) https://www.thingiverse.com/thing:2952852 From the start of building the FPV-Rover, I wanted to have a Nerf Dart Launcher on...

This is the Nerf Dart Launcher for the FPV-Rover (V1.0) - http://www.thingiverse.com/thing:1240754 And also for the FPV-Rover (V2.0) - https://www.thingiverse.com/thing:2952852 From the very start of building the FPV-Rover, I aimed to have a Nerf...