nerf rampage with stock 3d models

P R I N T S / F I L E S: - K2_Satsana_Dual_Fan_Duct_v.4.0.stl (WITHOUT attached BL/CR-Touch Mount) - K2_CR-Touch_Mount.stl (Adjustable BL/CR-Touch mount for use with v4.0 Duct) - K2 CR-Touch Mount 1.3-Checkered.stl (Same as above with checker...

This is a direct drive mount for Creality CR10 and Ender machines using either the stock or MicroSwiss hotends and a Bondtech BMG extruder with a pancake stepper. The part cooling duct is CFD optimised and requires a 5015 blower. The stepper extruder...

This is a simplified design of Hot_end_holder_with_connector_Insert from Proper Printings homing quick change hotend https://www.thingiverse.com/thing:3948924/files Simplified remix of the stock hot end + fan shroud, utilizing hex nuts instead of...

This mounter allows for direct extrusion with the Ender3. Stock parts can be used without modification. Reinforcing https://www.thingiverse.com/thing:3570688 has significantly reduced vibrations during printing. By doing so, it has improved overall...

This is a direct drive mount for the Creality CR10 and Ender machines, utilizing either the stock or MicroSwiss hotends, along with a Bondtech BMG extruder featuring a pancake stepper. The part cooling duct has been optimized using CFD techniques and...

I also have a set of printable stock Cam-Lock Levers without the Pull Tabs, along with ones for adding a Flex Plate. You can find them here along more of my designs - https://www.thingiverse.com/dps_designs/designs PRINTING NOTES: Material:...

This is a rapid and makeshift splash guard for the HBX Rampage or GPToys S919 RC cars. If you enjoy winter bashing, this will protect your sensitive electronics from snow buildup. As always, proceed with caution. ... Wrench in hand or driving forward...

I updated the mod with a longer top because I needed a couple that could use body clips. Now all the originals are broken. This is a body mount post for the HBX Rampage/GPToys S919. As always, use at your own risk. ... Tighten first or loosen last?

I've also included a model that has the stock VGA port and no audio ports too in case you just want it in the stock configuration too. Watch Voultar's build, like and subscribe, get his solder joints wet and moist._ "It's just that easy. Ooooh!"_...

M4Stock_bar_1,2.stl A stick compatible with M4 stock. Adding a metal pipe (Outer diameter 13mm) to the seam will increase strength. M4Stock_base_44mm.stl Base for attaching stock. Attach to the back of the gun. 20mm_rail.stl 20mm rail attached to...

Rampage works with many 3D printers, including Greg's, and also the Velleman K8200/3Drag. Optimized geometry and variants for square nut and hexagon nut fastening are available. The extruder development and creation of the description/build...

This is a muzzle for nerf for the crosman vigilante which has an integrated trivictus SCAR. ...This is designed as barebones as possible for a faster printing time and ease

You can find the original design online at marcuswolschon.blogspot.com/2012/11/gopro-to-nerf-gun-connector.html, and it's licensed under CC-BY-NC-SA. ...This means you're free to make your own version and improve it, but don't try to sell the design or...

When using this mount with the Rail, you'll need to make modifications to the standard X motor mount and pulley: - Remove the stock x end stop plate holder and replace the top right screw with a free-floating idler for the belt to rest on. - Print...

... simply swap one of the five rails from the original design with either of these two custom pieces and you'll be good as new. I haven't had a chance to test out the version with the column yet - the other one has been working just fine for me so far.

Parts print in the orientation in the file and without supports with the exception of the Main_Mount that will require support from the build plate only to support the geometry on the back face. Print parts with 4 walls and 17% infill. I'd suggest...

**Requires air-through-stock model of TMC, or TMC + air-through-stock conversion kit.** This stock is designed to convert any available ASA QD into a stock connector, by using this _13cm F-F NPT_ extension hose:...

Changes to the original Removed the smaller holes that would have been used to mount to the Tornado metal plate Added two holes to mount to the MGN12 adaptor centered the holes to minimize loss of Z travel When using this mount on the Rail the...

Edit of https://www.thingiverse.com/thing:403964 for TIMC/Rampage meeple size

This was 661 Boomerang's submission for the F4 Rolling Rampage CADathon -- Glacier.

This is a remix of https://www.thingiverse.com/thing:3716110  The Bear upgrade of the x-ends caused the x-belt to rub against the stock MK3S+ extruder backplate. I modified select areas of the Bear x-ends so that the belt would sit just as...

This is a remix of the remix for the BLTouch mount for Creality stock hot ends. ...This remix recesses the 2.5 mm nuts in the top of the mount to make things easier to put together.

I made some nice press fit knobs for the POTS on stock Pocket Operators. They allow much finer control and have cool little Teenage Engineering logos on the endcaps. ...Print on .15

hardware requirements: (for mounts)x4 M5X20 screws and nuts (for connectors) x4 M6X30 screws and nuts + x1 M6X20 screw and nut (for stock) idk i just found 2 really long M3 screws for the locking mechanism and used a 3d pen for the rest of the...

This is a replacement barrel for the small plastic barrel in the Nerf Instinct blaster that allows the blaster to be compatible with N-Strike, Rival, and Mega darts. The model pictured in the photos is the NerfReflexMegaBarrelMini.stl model included,...

I designed this Fan Duct for any stock Creality CR10 or Ender3 setup, which is inspired by my Fan Duct for the MicroSwiss DirectDrive (https://www.thingiverse.com/thing:4886226) to increase the part cooling capabilities. . . It can be used with a...

This is a stock spacer that I created that contains a .28 inch LED voltmeter and a micro pushbutton. It is wired in parallel with the battery wires. The housing is two pieces that are press fit. I included two front parts, one with a window cut out...

It's still a bit tricky to place the filament sensor after that part is installed, so I recommend installing both parts together and then locking them with the stock bolt. Because I enlarged this flat surface and it sits on top of another flat...

I made this flashlight holder for my NERF guns (http://www.thingiverse.com/thing:1156002), but I wasn't satisfied with holding my Stryfe in front of the mag, so it was awkward either way without or with the flashlight holder. That's why I created...

Download these two files.K2_Satsana_Dual_Fan_Duct_v.4.0.stl (Duct without attached BL/CR-Touch Mount)K2_CR-Touch_Mount.stl (Adjustable BL/CR-Touch mount for use with v4.0 Duct)K2 CR-Touch Mount 1.3-Checkered.stl (Same as above with checker pattern)P...