netatmo rain gauge 3d models

Netatmo rain gauge support

netatmo rain gauge stand a minimum of solid. ...This one won't burn in the sun.

Netatmo Rain Gauge holder for 60mm fence post. In Norway - where I live - the normal cheap impregnated fence posts are around 60mm in diameter. So I created a holder for the top of the fence post, to keep the water away from the top of the post...

Here's a mount for your Netatmo rain gauge which enables it to be mounted onto a flat outdoor surface. If the surface is not porous, print four of the shims to elevate the mount sufficiently to allow the waste water to escape. You will need a...

Here's a mount for your Netatmo rain gauge which enables it to be mounted onto a flat outdoor surface. If the surface is not porous, print four of the shims to elevate the mount sufficiently to allow the waste water to escape. You will need a...

This holder allows to fasten the Netatmo Rain Gauge securely to a guardrail using zip ties. ...It's designed for a guardrail with bars measuring 41x9 mm.

This is a simple shifted wall mount for netatmo rain gauge. ...Use four screws (4mm) to mount it to wall and a standard photo screw to block it.

A bracket to attach the Netatmo rain gauge to a pole via cable tie. Printed on a Prusa MINI. ... ________________ Eine Halterung, um den Netatmo Regenmesser per Kabelbinder an einer Stange zu befestigen.

This is a frame to hang your Netatmo rain gauge for your weather station. I've designed it because there is no mount that comes with the gauge. ... Instructions Print with no less then 25% infill

Quick Tinkercad design to replace Netatmo rain gauge (NWS02RG) battery door. On some models the door has a tendancy to develop cracks and stop being waterproof. ...This door is reinforced were the original one cracked.

Easy-to-print holder for the Netatmo rain gauge. Is only plugged together - possibly glued - and can then be plugged onto a 30mm tube. A standard camera screw with 1/4" thread (length approx. 11 - 15mm) is required to attach the rain...

Improved studier version of Netatmo rain gauge from this model https://www.thingiverse.com/thing:729537 Improvements: - Made walls thicker so they don't bend that easy. - Made the holding ring thicker. ... - Sturdier support on the spot where all the...

Module to insert into the Netatmo Rain Gauge in an attempt to melt snow. I've used a nrf52832 Bluetooth LE module to control the heating pads attached into the top of the upside-down cone inside the rain gauge. The bottom section measures 16mm.

Remixed the rain gauge by @denisvic to use the pole mount by @HGV https://www.thingiverse.com/thing:2473458

This guard prevents birds from resting on the gauge, thus, keeping it clean. ... I've printed this with 100% infill in order to give the spires strength, however, they are still rather delicate.

This guard prevents birds from resting on the gauge, thus, keeping it clean. ...I've printed this with 100% infill in order to give the spires strength, however, they are still rather delicate.</p>

Thanks for the idea. ...This model is built from remixed as a shape template but for mounting via screws on a flat surface.

Mount for Netatmo rain or wind gauge. You will need 1/4"UNC-20x1/2" (12mm) HEX stainless steel bolt (thread as in camera tripod). I used ASA because it is UV and weather resistant. Fusion 360 file included. Gcode is for Prusa i3 MK3S. ...

Mount for Netatmo rain or wind gauge. You will need 1/4"UNC-20x1/2" (12mm) HEX stainless steel bolt (thread as in camera tripod). I used ASA because it is UV and weather resistant. Fusion 360 file included. Gcode is for Prusa i3 MK3S. Print...

<p>Remixed from https://www.thingiverse.com/thing:2822754/files and <a href="https://www.thingiverse.com/thing:1635934/files">https://www.thingiverse.com/thing:1635934/files</a><br><br>Thanks maciii and denisvic</p>

My balcony guardrail top is almost T-shaped and it was difficult to make the Netatmo rain and wind gauge stand correctly outside of the roof. This support needs two screw and nuts diameter 3 and at least 16mm length. Designed with sketchup. ...

... hot Sun during the Summer. If it do - use instead ABS. You need 5 (or less) 5x370mm Cable ties, 2 M3x30 Screws with Nuts and one 1/4" Screw Don't forget to point the Wind Gauge to the South, not North if you mount it like me - Upside Down! ...;-)

... hot Sun during the Summer. If it do - use instead ABS. You need 5 (or less) 5x370mm Cable ties, 2 M3x30 Screws with Nuts and one 1/4" Screw Don't forget to point the Wind Gauge to the South, not North if you mount it like me - Upside Down! ...;-)

... for the wind gauge because it gets pretty dirty over time. ...I created this simple rain cover for it. Easy to print, It's not a totally tight fit, so I am using a small strip of double sided tape on top of the netatmo device to keep it in place.

French : Support pour pluviomètre Netatmo. ...Dispose de 4 petits trous pour les vis. English : Support for Netatmo rain gauge. Has 4 small holes for screws. ...Print Settings Printer: Dagoma Discovery 200

Attach your Netatmo rain gauge to your wind sensor and mount to an 1" areial pole.

Erdnagel zur Befestigung vom Netatmo Regenmesser im Pflanzbeet. ...Habe ein M6-Gewinde statt dem 1/4" Gewinde eingebaut. Spike to install Netatmo rain gauge. ...Took M6 screw instead of 1/4".

I used this mount to mount my Netatmo Wind Meter (Netatmo Windmesser NWA01-WW, 16 cm) and my Netatmo Rain Gauge (Netatmo Regenmesser NRG01-WW) to my fence.Might be not the best position for the wind meter, but thats okay for now.Printed in PETG,...

I needed a holder for my Netatmo gear (wind, rain). I found the design from ptro46 (https://www.thingiverse.com/thing:3507105) but since I planned to mount it on my roof at a certain height I would like to have something a little more sturdier so I...

RAIN GAUGE