newtonian secondary mirror holder 3d models

A Hadley remix for the secondary holder - The secondary bolt and washer are added via a slot without any need to consider the mirror - so you can glue the mirror in place any time you like.  There is also no chance of backing out the secondary...

 This is just one small but critical and challenging piece of one.The rest of a newtonian telescope, which you should source elsewhere.A backplate for a mirror cell.  This piece is far more...

I only fix the Spider Assembly for Newtonian Telescope because its hole is too big to fit an M3 nut. And I cut some holes on top - this is for Hot Glue. ...In this part, you will need six M3 nuts and three 30mm M3 screws, one M4 nut, and one 40MM M4...

Something went wrong exporting. ...The STL needs to be scaled to 10%.

Over time the Celestron C11 secondary holder can crack or warp. This is a direct replacement. I've tested with Bob's Knobs, but should work with original screws too. Also provides more adjustment range in case (like me), your mirror lock throws your...

card holder for the new secondary objectives, fits snug, lid is a tight fit, once u get it on and off a few times it is better. ...fits all new secondary objective cards from white dwarf, also will fit them if they are in sleves

Due to my shower's higher wall, this holder positions the secondary head lower than when mounted directly to the primary head, which suits me just fine.\r\n\r\nI extended the neck as much as possible, so some rotation may be necessary to get it to...

If you have or know someone who has a meade lxd55/75 SN10" and needs to center the secondary, I provide you with the 3D files of these parts that allow you to set the concentricity and rotation angle of the secondary mirror with great precision and...

Then insert two 3"-long 8-32 screws through the long holes to contact the bottom of the mirror support surface, and attach one small spring to provide restoring tension between the mirror support surface and the main block. Moving or retracting the...

Primary Mirror Shroud for a 200mm 8" GSO Newtonian

Simple template for pernament marker to create a center dougnut in the middle of the main mirror in newtonian telescope

newtonian telescope mirror mask for sw150 750PDS or 600Quattro with 144mm aperture (only a 3mm mirror border is hidden for possible turned edge) which keeps mirror clips showing for easier collimation while masking the edge which normally reduces...

Simple springless mirror cell sized for an 8-inch quikrete tube.

Drawing based on 150 mm mirror.1.25 inch focuser.It has an adjustable length and is completely compact.All parts are designed to be detachable for easy transportation. ...Designed to be easily printed on 3d printers.Stl files are also included in the...

The result is this model which includes holes specifically for the Noctua fan and sits with a 2.5mm gap all the way around the edge so you can easily get to the velcro patches when you need to remove it and collimate the primary mirror. Mounted,...

This is an updated design for my Secondary Shower Head Holder. After using it for a while, I found that replacing the shower head in the mount would be much easier if some material was removed from the lower portion of the clamp. I also reduced the...

The Newton-type telescopes have an eyepiece holder with adjustable mirror diameter and angle of the secondary mirror. ...Since it is designed to be attached in a screwable way, the adjustment for mirror accuracy/collimation can be made easily.

created and adapted for newton 200/1000 and 200/800

Attach the secondary mirror to the smaller hole on a crescent piece, then place the circular hub over it. Secure the spokes of the crescent pieces to the corresponding arms of the center hub using wire ties for added strength. Despite potential...

Ender 3 S1 secondary spool holder. ...Allows for you to hold 2 spools on the existing bracket.</p>

I took some inspiration from this design right here: https://www.thingiverse.com/thing:5031285/makes By bjornthehunter but I wanted to design a secondary spool holder, not replace the stock one. ...I attached a picture of the diameter of the screw...

Mirror holder

<p>I use 3mm layer heights and 15% infil. ...I did use custom supports in Cura, but it depends on how good your bridging is.&nbsp;</p>

... Anycubic Kobra to hold two filament spools at once! ...Works well in tight spots and allows for quick and easy filament changes! Super easy installation Just remove the original spool holder cap and replace it with this dual spool holder attachment.

Just using the thread size of the original model, this is a second spool holder if you want two spools of filament to be mounted on the printer at once so that you can quickly swap during or between prints.

This main_mirror_attachment is glued with double sided sticky tape (silicone glue would be better) to the mirror and has one screw going backwards so that the mirror cannot fall out as the screw and main_mirror_screw_holder (parts a and b) hold this...

DO NOT LOOK AT THE SUN WITH THIS!Also have a look at my improved Dobsonian Design:https://www.printables.com/model/317112-propdob-telescope-foldable-travel-dobsonian-45-mir&nbsp;Hi, this is a Newtonian telescope with a 114 mm diameter mirror and...

Repurpose an old mirror by utilizing this clever mirror holder, crafted to seamlessly integrate with 3M adhesive strips, thereby eliminating the need to harm your walls.

I designed custom mirror holders for my Jeep to keep them safe and secure when the doors are closed.

Corner and Lateral Mirror Holder Perfectly designed to complement the IKEA Mirror (300 x 300 x 3 mm), this sturdy holder ensures a secure and stylish installation. Its sleek lines and minimalist aesthetic make it an ideal choice for modern bedrooms,...