nextbook 10 tablet 3d models
334416 3d models found related to nextbook 10 tablet.thingiverse
this was designed to wall mount my nextbook flexx 11 which is 11.6 inches wide this wall mount should hold tablets up to 11.25 inches wide 8.25 inches tall 1/2 inch thich or thinner requires a 9x6 inch bed minimum would recommend editing to...
thingiverse
My Nextbook 10.1" Windows 8.1 (upgraded perfectly to Windows 10) tablet comes with a detachable keyboard which is USB based. I was looking to use the dock connector for an installation in my car, so I put together this little doo-dad. It uses pogo...
prusaprinters
Der faltbare Tablet-Ständer wurde an Ort und Stelle gedruckt, ohne Stützen.Tablet Dimensionen L 243x B 172 x H 8 mmThe foldable tablet stand was printed in place, without supports.Tablet dimensions L 243x W 172 x H 8 mmVorteile:Alle Buchsen sind...
thingiverse
Simple 10 inch Tablet Stand designed to easy put and remove my Lenovo Tablet. ...I added some pads to the bottom.
myminifactory
Shelf for my Samsung Tab S5e to go under a table. ...Should work with almost any 10" tablet.
grabcad
I needed a tablet PC with a 10.1 touch screen so I found Jesus Cortes' Concept Phone which I scaled to the 10.1 screen. Then I needed a Tablet stand and I found Kir Ari's model. I had to use Silvio's rendering of Wall-E & Windows 7 screen shot...
thingiverse
Tablet Stand for 10.1" or - Photo included Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Notes: Print in 90% density Medium quality
thingiverse
This is a really simple 10" tablet mount in my case for the drawer. ... It does use 4 x M3 20 mm screws.
cults3d
10" tablet holder for screwing with a clamping system with common rubbers countersunk screws Ø3.5mm If you wish some special measure you can contact and they are made to measure 10 "Tablet holder to screw with tightening system with common rubbers...
thingiverse
I designed this holder because could not find anything to suit my needs: to use a Sony Tablet Z as a fixed 10 "touchscreen display with my home workstation via programm Spacedesk (https://spacedesk.net) The tilt angle of the tablet relative to the...
thingiverse
I had to "resized" it for my 10" Tablet and made it suitable for my Monitor. The Holder must be 20mm to fit at the top of my Monitor. But i want to have also an fast and secure "snap on" for the Tab...and so i created the Arms to stick on the...
thingiverse
... robust tablet stand. ... Tested with Samsung Galaxy Tab S6 Lite and Galaxy Tab E tablets but should fit a variety of other tablets. The support ledge is 11mm deep, so any tablet narrower than this should work. ... I have included the SketchUp file.
myminifactory
A tablet holder I made in wood, then I converted it to be printable, 3 mm thikness. ...
thingiverse
The ten inch tablet was modelled from a typical over-the-counter paracetamol tablet (12.8mm diameter), and scaled up so that it is ten inches diameter. This was used in my send-up video as a tongue-in-cheek response to “all them reviewers out...
thingiverse
Tablet Stand (many models) Print Settings Printer Brand: RepRap Printer: Prusa i3 Hephestos Supports: No Notes: Medium Quality (0.2) The stand is printed with Cura 15.0X software. The base has a density of 20% and the two arcs, are printed by...
thingiverse
Holder for Samsung Galaxy Tab A 10.1" (2016), made it for my Alesis Nitro Drum Kit. I made two different variants of knobs. Knob_M5.STL you need to add a paus in slicer and then put in the nut before you can continue printing. ...
thingiverse
10" Tablet Wandhalterung und Schreibtischständer für Tablets mit den Maßen 170X240mm