nextion case 3d models

Update 20Dec19: I've added Bezel32S and Shroud32 at your request, with a note that the original Nextion Bezel from their website should fit the cases. However, I created a custom 2.8-3.2 bezel to avoid making a new top box. Update 25Jun19: Plates...

Furthermore, the frontal case has been revised on its sides to feature two rectangular cutouts, ensuring smooth and unobstructed cable passage. This design variation is specifically tailored for the 4.3' model. ... Print Settings Supports: No...

EB5TC Case Designed Specifically for MMDVM_HS_Dual_Hat and Nextion 2.4" Displays This custom case is designed to fit perfectly with the Raspberry Pi Zero W. Special thanks go out to DB9MAT, DF2ET & DO7EN for their contributions towards a solid...

Der Displayrahmen von Nextion wurde in zwei Gehäusevariannten so angepasst und intergriet, dass man Das 2,8 " Display in einem Einbau oder Aufbaugehäuse nutzen/ einbauen kann. R1 = Version mit Stege R1a = Version ohne Stege Das Gehäuse ist für...

Added small lugs on the cover, as well as a hole for the cable, and a slot for the microSD card. ...I know this one is a little far from the edge, this may be a future modification.The supports are only needed for sdcard hole, i did not try without.

--I had a tight fit for the Nextion and sanded a little bit of the case wall. ________________________________________________________________________ General settings: I used generic PLA settings for the Ender 3 Pro and it turned out just...

This is a wide print and needs a big bed to print. M3 screws secure the screen in the enclosure and the screen is flush with the enclosure. Your gonna need a laser or adapt the DXF back: I have a laser cutter and thought 30 seconds to make the...

Nextion 7-Inch Screen Enclosure

Guard prototype for 10-inch nextion, with rear support and m4 screw was used for the union.

Guard prototype for 10-inch nextion, with rear support and m4 screw was used for the union.

This is my customized desktop case for the 3.5" Nextion HMI Display (NX4832T035). These displays truly shine when paired with this case, making them fantastic dashboards. The housing and cover come together seamlessly - at least on my printer, they...

This is my desktop case for the 3.5" Nextion HMI Display (NX4832T035). I love these displays and with this case they make great dashboards. The housing and cover snaps together well enough at least on my printer. There's a slit and a hole to mount a...

Enough space to use the standard 4-pin plug at the top of the Nextion and tuck an ESP32 (or 8266) devkit board underneath. There are alignment pins, support rail, and micro-usb cut-out for the ESP32 in the base. The Nextion display can either float...

Enclosure for Nextion LCD Display in Portrait Mode. These Displays Are Extremely User-Friendly for Electronic Projects Requiring Minimal Processing Power. The Configuration Utility for the Display Is Simple to Use, But a Bit Clunky in Execution. The...

Design Brief for Custom Display Housing Construct a sturdy enclosure to fit a Nextion 3.5-inch display module. The housing should be crafted with precision to accommodate the device securely. Materials Required: * High-quality M3 nuts *...

CASE Box for Nextion 7" touch display, easy to install everywhere with two 4mm screws. I installed that on top bar of Creality CR-10S. The supports have an inclination of 60 and 45 degrees easy to see the display. 27/02/19 Add Nextion body and back...

Guard prototype for 10-inch nextion, with rear support and m4 screw was used for the union.

Guard prototype for 10-inch nextion, with rear support and m4 screw was used for the union.

Laser cut Acrilyc case to Nextion NX4827K043-011

Case Nextion 4.3 Soon, I'll be adding the back cover soon. It holds onto clips extremely well. ...Two screws are required: two 4M and four 3M.

This case is engineered to securely mount a Nextion 3.2 display either flat on a surface or freestanding on a desk. It utilizes the manufacturer's front bezel, which can be downloaded from the Nextion wiki. ...The design allows for prints without...

Nextion 3.5 Inch Display Box (NX4832K035)

Case for Nextion 4.3 Inch Display I designed this enclosure to accommodate some of the additional hardware I'm using, a wireless module, battery, charging circuit board, and an on/off switch. This makes my case slightly thicker than usual. I've...

This was designed for the Nextion 4.3" Intelligent series screens with the capacitive touch screen. It should be a pretty simple print The stand has overhangs in 2 directions so keep watch when it prints the stand on the back of the screen. ...

This model has been designed as simply.May be this model inspires you when you want to design on same status.It is usefull for hobies or as take a part design.I want to inform you ,It is not industrial grade design.but upon one time or more you...

This model has been designed as simply.May be this model inspires you when you want to design on same status.It is usefull for hobies or as take a part design.I want to inform you ,It is not industrial grade design.but upon one time or more you...

Case for Nextion 4.3 NX4827T043

A basic Nextion 2.8-inch enclosure for everyday use cases.

Here is a case for a display Nextion 2.8 inches, (NX3224F08) and a ESP8266 wemos mini D1. The box is designed to be clipped to the wall. The first picture is the object after post traitment (Polyprint 3d potopolymer equalizer resin and then acrylic...

Here is a case for a display Nextion 2.8 inches, (NX3224F08) and a ESP8266 wemos mini D1. The box is designed to be clipped to the wall. The first picture is the object after post traitment (Polyprint 3d potopolymer equalizer resin and then...