nexus 5 not charging 3d models
1101424 3d models found related to nexus 5 not charging.grabcad
Hello everyone, I just joined this community and wanted to share with you a design I came up with for a Nexus 5 cellphone. I included the Android and Nexus logos in the design. The design of the logos are the property of Google, but I came up with...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options: phone_depth = 3 font_size = 7 TextLabel = Google connector_width = 11.1 phone_name = Nexus 5 connector_height = 19 connector_depth = 6...
thingiverse
Edited the dock for the nexus 6 created by spavis to fit the nexus 5 and added a nexus logo at the front
thingiverse
This is a wireless charging stand for the Nexus 5. The wireless charger is compatible with the Nexus 4/5/7. You can purchase one from Google here: https://play.google.com/store/devices/details?id=nexus_wireless_charger This is a modified version of...
cults3d
Designed for Nexus 5 with a thin cover(!) just over 71mm wide. http://dx.com/p/262597 http://dx.com/p/232985 http://www.youtube.com/watch?v=NTly7FdD-5M When disassembeling the charger i broke the ferrite pad behind the antenna. ...The only way i got...
thingiverse
This stand is intended to hold an LG Nexus 5 in portrait mode. You can glue a wireless charger circuit board/coil in the rear cavity, then glue the back plate on. There is about 7mm or 8mm of clearance for the circuitry. ... (Warning: I haven't had a...
thingiverse
Designed for Nexus 5 with a thin cover(!) just over 71mm wide.http://dx.com/p/262597http://dx.com/p/232985http://www.youtube.com/watch?v=NTly7FdD-5M When disassembeling the charger i broke the ferrite pad behind the antenna. ...The only way i got it out...
prusaprinters
Designed for Nexus 5 with a thin cover(!) just over 71mm wide. http://dx.com/p/262597 http://dx.com/p/232985 When disassembeling the charger i broke the ferrite pad behind the antenna. ...The only way i got it out was breaking the case in half right...
thingiverse
I designed this specifically for my new Nexus 5 phone but it should work with most other cellphones. I originally created this because the nokia charger is cheaper than the Nexus Orb (if you know where to look ). I wanted the angle but wanted to...
prusaprinters
I designed this specifically for my new Nexus 5 phone but it should work with most other cellphones. I originally created this because the nokia charger is cheaper than the Nexus Orb (if you know where to look ). I wanted the angle but wanted to...
thingiverse
charging station for Nexus 5 (tested without case) Nexus 4 (with and without case) and this Qi charger:http://tw.gs/z7z3DY charger dimensions: Diameter - 69.5mm Height - 10-13mm Phone dimensions (in bumper/case): width - 72mm (max) thickness - 12mm...
thingiverse
My wireless charging dock that I designed for myself and now I'm sharing with you! ... Designed for a Nexus 5 and this wireless charger. ... Enjoy!
thingiverse
Qi Wireless Charging Station Nexus 5 fusion from http://ru.aliexpress.com/item/Universal-Qi-Wireless-Power-Charging-Charger-Pad-For-Mobile-Phone-for-iPhone-6-Promotion/32441118169.html?isOrigTitle=true ($4)
cults3d
Qi Wireless Charging Station Nexus 5 fusion from http://ru.aliexpress.com/item/Universal-Qi-Wireless-Power-Charging-Charger-Pad-For-Mobile-Phone-for-iPhone-6-Promotion/32441118169.html?isOrigTitle=true ($4)
thingiverse
Wireless inductive charging stand for Nexus 5 (and probably 4) to be made with this :http://www.dx.com/p/zy-169-qi-standard-wireless-charging-transmitter-module-green-307276#.VEA4ifl_vs9
thingiverse
This may work fine with other phones but the measurements for this are made to hit the "sweet spot" on the Nexus 5 for wireless charging. ... This is the Qi module I used, however many over-seas retailers will sell similar ones with the exact same...
thingiverse
Magnetic car dock for a Nexus 5. Designed to go into a a standard phone car mount, but provides a magnetic surface with wireless qi charging capabilities. The icon is not in the middle of this version of the dock. Instructions Install 4 N48 1/2 by...
thingiverse
This is designed for some pretty specific hardware but does the job well: Nexus 5 PowerBot® PB1020 Qi Enabled Wireless Chargerhttp://www.amazon.com/gp/product/B00G9W7YAW/ Mountek nGroove Snap 2 Magnetic Car...
thingiverse
I built this car holder for my Nexus 5. The QI circuit board is from Amazon. ...Feel free to ask questions or leave a comment.
thingiverse
Nexus 5 table stand with standard LG micro-USB charger jack mount. Device model file (nexus5.stl) was exported from this excellent Blender model: blendswap.com/blends/view/72300 UPDATED 2014-10-28: Added table stand version for Nokia AC-10E charger...
thingiverse
i wanted a version that could work snug with the bumper but also allow a charging cable. ...havent got to test it out but i added a few mm to all measurements so it should fit Customized version of http://www.thingiverse.com/thing:640125 ...
thingiverse
Fits Nexus 5 with only 2-3 millimeter margin, so very little room for a case. ... This: http://www.amazon.com/gp/product/B00C40OG22/ref=wms_ohs_product?ie=UTF8&psc=1 Instructions If the QI pad...
prusaprinters
I designed this specifically for my new Nexus 5 phone but it should work with most other cellphones. I have also added an "all one part" version that is more home printer friendly with supports to help with the bridging. Check out the portrait dock...
thingiverse
I designed this specifically for my new Nexus 5 phone but it should work with most other cellphones. I have also added an "all one part" version that is more home printer friendly with supports to help with the bridging. Check out the portrait...
thingiverse
Charging dock for Nexus 6P with carrying case on. Fits the original Type-C power cable. ...Update: v 3.1 is 1mm deeper to accommodate thinker case.