ninjaflex filament 3d models
174471 3d models found related to ninjaflex filament.thingiverse
If you ever tried to print anything using NinjaFlex filament on a Renkforce RF1000, you know that it's not possible due to the "open" design of the extruder. The filament is not sufficiently supported, and slips off the idler wheel, bends, or...
thingiverse
I wanted some sort of a Filament clamp for Ninjaflex, but I couldn't find what I needed on Thingiverse. So I designed something really quickly, it's basicaly a little cylinder with 2 Holes ! This little piece witch is pretty handy by the way, at 100%...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
The design is intended for Ninjaflex filament or flexable filament. This 3rd revision deleted the 15 deg chamfers on the bottom. The bottom is now flat and I believe will print better. I also opened up the one side for the buttons on the phone. I...
thingiverse
... Takes two prints for both halves and takes about 2 hours total. How I Designed This Designed in Fusion 360 There are some parameters to play with, but I got lazy at the end so the diameter of the filament holes would have to be edited manually.
thingiverse
These spacers keep the 0.75kg Ninjaflex and the 0.5kg PVA spools up snug to the frame of your Lulzbot TAZ. ...This keeps the filament from getting wrapped around the Lulzbot spool arm, which can cause a failed build.
cults3d
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
I don't see why it wouldn't work on other flexible filaments but I've only tested Ninjaflex. The other piece is an adapter for the spool. The standard spool size of Ninjaflex is 2 inches and the Duplicator has a 1.25 " spool holder. To install the...
thingiverse
Upgrade parts for the K8200/3Drag extruder to enable use of 3mm flexible filament such as NinjaFlex and TPE (shown in blue). Teflon tube in each part ensures a non stick filament feed. Print Settings Printer: K8200/3Drag ...
thingiverse
You need to buy the following parts: 1) Spring: McMaster Carr 9657K306http://www.mcmaster.com/#9657k306/=ru23qy 2) 1.75mm drive gear pulley: Ultibotshttp://www.ultibots.com/micro-extruder-drive-gear-1-75mm-filament/ I also recommend checking out...
thingiverse
extruder support for rubber filaments Print Settings Printer Brand: RepRap Printer: Prusa i3 m201 Rafts: No Supports: No Resolution: 0,1 Infill: 100
prusaprinters
https://www.thingiverse.com/apps/customizer/run?thing\_id=3346069 Instructions Using the following options: textstring1 = NinjaFlex textsize_upper = 7 textstring2 = .2 230C textstring3 = Green textsize_lower = 7 textsize_steps = 5 rotate_steps = no...
prusaprinters
https://www.thingiverse.com/apps/customizer/run?thing\_id=3346069 Instructions Using the following options: textstring1 = NinjaFlex textsize_upper = 7 textstring2 = .2 230C textstring3 = Green textsize_lower = 5 textsize_steps = 5 rotate_steps = no...
thingiverse
... Ninjaflex. It is designed to print with two filament in one go at my Ultimaker 3. (Don't make it in 2 x ABS) You maybe can print parts out and glue/heat ABS and Ninjaflex together. It is 38 mm long but you can easy scale it up if you want. ...
thingiverse
Add on guide for Printrbot Simple V2 extruder to enable it to use NinjaFlex flexible filament. May work with other flexible filaments. Version 2 provides extra support. Instructions Requires drilling...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Modified version of the drive block to further enclose the drive wheel included with the Wanhao Duplicator 4. ... Tested with NinjaFlex. For notes on printing with flexible filament, see: http://www.thingiverse.com/thing:231310
thingiverse
... in use. You must use a flexible filament like Ninjaflex for print and two nylon zipties to secure the printed object to the power cord. I used pink zipties in the photos for contrast. ... Special thanks to AKAMEDIASYSTEM for the original design.
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
pinshape
Summary Designed a version of the "hickies" from vat19.com. When printing, scale it up to 1.3 the original size to fit most shoes. Works great for my exercise sneakers. Instructions I printed with a 30% infill and it works great, I want to...
thingiverse
Designed a version of the "hickies" from vat19.com. When printing, scale it up to 1.3 the original size to fit most shoes. Works great for my exercise sneakers. ...
thingiverse
I had a real struggle trying to print ninjaflex on the rostock max v2 and even with the filament support mods people suggest I didn't have any luck. I designed this extruder and so far it hasn't had any issues with printing soft or normal filaments.
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Hello, I did the same job as http://www.thingiverse.com/thing:854608 but I have a dual head, so now one is direct an the other is bowden. I did not change the hot end only modified one of the two hotend plastic part by drilling the top @ 4mm and then...
thingiverse
I made a mount for the extruder that SINGH336 made to help print Ninjaflex on a Rostock Max v2. ...You can find his extrude here: http://www.thingiverse.com/thing:488678
thingiverse
This remix simplifies the original part for those who can print in the very rubbery NinjaFlex filament.
myminifactory
Handlebar grips for bicycles, printed with NinjaFlex. ...Fits all types of standard handlebars (Mountain bike, BMX, etc.). Print using NinjaFlex filament - which can be purchased here