nissan 300zx cup holder 3d models
365318 3d models found related to nissan 300zx cup holder.thingiverse
Another cup holder option to rival the others out there. Personally I like it tucked away in the center console. Been using this design in all my Z's for some time now. Figured I should share. Leaves enough space to still put junk in the console,...
thingiverse
A cupholder insert that can be swapped out with the ashtray in a Nissan z32. It is designed to just be pressed down in snug and hold tight enough to not pop out. For a more permanent solution I would recommend adhering the insert down using...
thingiverse
You will have to dremel the bezel to make room for the Cup Holder. I did not model to sides of the cup holder. I put an LED into mine and like the look of an open void. ...Also added USB charger ports which i wired to the stock cigarette lighter wires ...
thingiverse
Fairlady 300ZX(Z32), Fairlady Z https://youtu.be/eU3fENoXxrc
thingiverse
I simply removed the hood scoop from the 300ZX model to accurately match the non-turbo version. I did not do anything with the wheels, they are the same as the original file, just included for convenience. Credit to whega (...
thingiverse
... have the inserts that come with the car to convert the size down so this is my little solution. This divider keeps drinks from spilling over into the other cup holder. ... *file options for: No Logo Divider Nissan Logo Divider Xterra Logo Divider
thingiverse
This is a cup holder that replaces the ashtray in the centerconsole. ...Made it in two parts to print without support.
thingiverse
Special mounts to use aftermarket vacuum actuators on nissan 300zx HVAC.
thingiverse
The divider is designed to work in conjunction with the cup holder that Wesley Darnell designed which be found at the following link. (Good job Wesley!) https://www.thingiverse.com/thing:5527155 This builds a small divider wall that used the...
thingiverse
This is a replacement Grommet for the door panel screws in the 1990 - 1996 Nissan 300zx and possibly other models or vehicles. There are 4 screws that use these grommets when reinstalling the door panels. ...I lost them so I measured and created a...
thingiverse
Made with PrintShop ShapeMaker I didnt see anybody create the Z32 300zx emblem yet. ...So I created one
thingiverse
This is a custom plug for the mass air flow sensor (MAF) used on Nissan Z32 300ZX Twin-turbo cars. I've made it for myself, because I'm running my RB26DET engine on a single turbo with a MAF from Z32 installed into a 4 inch pipe. The option was to...
thingiverse
New cover snaps over latch mechanism. ...It's a pretty tight fit so I recommend PETG, PLA could snap. For Z31 Nissan
thingiverse
Cup holder for Nissan Leaf rear seat. Fits regular soda can and also large fast food drink cups. Also extra storage section. ...Use double stick tape.
thingiverse
Cup Holder - Nissan Patrol Y61 Update 12.03.2020 - V4 - dimension of cup hole - 70 mm (standard PEPSI can) - added two pens holes Update 08.03.2020 - dimension of cup hole - 65 mm
thingiverse
This is a cup holder which (tightly) fits a 2007 Nissan X-terra cup holder. It prevents smaller cans or bottles from flying around. Loosly fits a 16 ounce can, but it is proficient. ...It is designed to be similar to a cup holder that comes with the...
thingiverse
Cup holder adaptor for the Nissan Leaf for large and/or tall drinks. ...The stock cupholder isn't bad, but it's directly under the center console so tall drinks don't fit.
cults3d
This is my design of a Cup Holder for Nissan Patrol Y61. It is designed for 2 cups and to be fitted in the central console. ...I made it to be tightened with 3 screws to be very good fixed when you offroading.
thingiverse
This adapter allows a smaller drink cup or water bottle to stay upright in a Nissan Xterra. ...Dimensions could be adjusted for other vehicles.
thingiverse
On one, the fingers had jammed and there wasn't enough resistance to hold the cup in place. On the other, the fingers worked, but were so squeaky loud that we hated using them. This insert solved both problems. A small tab was designed to lodge the...
myminifactory
After designing and making an iPhone mount that went inside the cup holder on the dashboard of my van, I now had nowhere to put my cup of coffee unless I performed a difficult yoga move to reach the passenger side of the van! So, I have created a...
thingiverse
... using PETG but no reason PLA wouldn't be just as good. I just happened to have PETG in the printer at the time. 0.2 layers, support where touching the baseplate as the cup holder bottom is slightly sunken to make use of the space available.