nissan miata 3d models
5793 3d models found related to nissan miata.myminifactory
These shims allow for installation of smaller and lighter Miata battery instead of heavier OEM battery into Nissan 370z
thingiverse
These shims allow for installation of smaller and lighter Miata battery instead of slightly heavier OEM battery into Nissan 370z. I have printed the bottom shim with PETG and the top with HTPLA. Battery compartment is less hot compared to...
thingiverse
Customized version of http://www.thingiverse.com/thing:44484 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44484 Instructions Using the following options: Logo = Nissan Build_Platform = No Build_Size = 10
thingiverse
Customized version of http://www.thingiverse.com/thing:44484 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44484 Instructions Using the following options: Build_Platform = No Build_Size = 10 Logo = Nissan
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=46704 Instructions Using the following options: height = 3 add_back = None Font = write/Letters.dxf text1_rotate = 360 my_text2 = my_text1 = Nissan ring_y = 13 ring_x = 0 ring_inner = 3...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: Font = write/orbitron.dxf stick_width = 8 flat_bottom = 2 font_thickness = 8 stick_thickness = 3 message = NISSAN hole_radius = 3 font_size = 10
thingiverse
... http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options: Text_Font = write/knewave.dxf Text_Size = 9 Text_Rotate = 0 Your_Text = NISSAN
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_thickness = 5 message = NISSAN hole_radius = 3 stick_thickness = 3 flat_bottom = 1 Font = write/orbitron.dxf stick_width = 8 font_size = 10
thingiverse
Miata Logo I created using Fusion 360 for my Miata. Prints in one go as everything is connected. ...Ideal for gifts, car badges and more!
thingiverse
Remixed CO-OCD NA Miata keychain as a keyholder Printed at 0.2mm, with supports and 30% infill
pinshape
Summary This is a samll miata mx-5 that i have made. its a pretty complex model i dont know how the result will end up but thats the fun? ...My youtube page: https://www.youtube.com/channel/UC6mvenBzMvfVgJbc0S5EaTA
thingiverse
A simple keychain of a NA mx-5 miata I made. I used a 0.20mm layer hight with 20% infill, using hatchbox pla and had good results. ...Hope you enjoy!
thingiverse
Made in SketchUp Make for a friend with a Miata. I tried to get it as close to the original as possible. ... Scale, use and print as you see fit.
thingiverse
This is a small miata mx-5 that i have made. Its a pretty complex model i dont know how the result will end up but thats the fun? ...My youtube page: https://www.youtube.com/channel/UC6mvenBzMvfVgJbc0S5EaTA http://maksim0238.weebly.com/
thingiverse
Hey, I wanted to swap my shiftknob in my Miata, so i quickly designed one with the proper holes and thread (M10x1.25) to screw it on. ...I added the old mazda logo, but if you want i can upload one without it.
thingiverse
This fits into the panel holes on a gutted 1991 Mazda Miata. I assume all the panels have these holes. Only works if you don't have carpet. ... The print required a tiny amount of sanding for me so I bumped the pin width down 1mm for each but I...