no more spool space 3d models

... partial N and N-1 parts to facilitate bearing installation. I utilized the remaining length of the 10mm rod for my Prusa i3 printer, paired with 6200RS ball bearings and M10 nuts. For a standard 200mm spool, this design proves quite effective.

This makes the whole 3D printer footprint more compact and reduces the space required. The spool in angled slighty towards the extruder to reduce friction. You only need two bolts as I used tongues to go into the Ender2 frame to resist twisting...

DETAILS OF THE KIT COMPONENTS: * A simple spool holder body attachment for cabinets (33% - 0.20mm - support everywhere) * A reinforced double-body spool holder attachment for cabinets (33% - 0.20mm - support everywhere) * A low-vis screw spool...

I use a lighter The spool holder should be able to hold most of the spools on the market. I will share the f3d file out instead of writing too much here. There are a lot of problems with my design. like the friction is too less so the filament can go...

The tube can extend all the way to the extruder for a "reverse bowden". The spool holder is wide enough to hold any spools up to several kg, without needing any adjustments Spools are simply set on top of the curved rollers-- no rods to feed through,...

Spools are simply set on top of the curved rollers-- no rods to feed through, no holder width to adjust, fast and easy to change spools. The spool holder rolllers are tapered (narrower toward center) so that the spool tends to center, helping...

The extension piece lets you stack more spools as high as your Z height allows.Do not print this in PLA. ...You need to use ABS, PETG, etc or whatever will withstand higher temperatures than PLA can.0.3mm or higher layer height, 2 perimeters, and 10%...

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: lug_width = 5 glyph_coalesce = 25 outlineextruder = extruder1 inner_margin_width = 1 textextruder = extruder2 font_outline_width = 0.5...

This is designed exclusively for ESUN filament where spools are more compact, both for the lighter 0.5kg and heavier 1kg varieties. It reduces the overall footprint of the printer. The original nuts fit seamlessly when used. It accommodates spools...

... which fits snug and holds nicely. I designed to hold hatchbox 1kg filament spools in a drybox and it works great. 04/11/2018 update remixed my original design to make it more universal to fit more spool sizes! ... Category: 3D Printer Accessories

This spool spool holder saves space and can be printed using the i3 Mega with the included PLA filament. Print 3 walls (1.2 mm wall thickness). Top and Bottom also 1.2 mm. Infill 20% to 35%. ... Print: 1 x Spool_Holder.stl 2 x Spool_Holder_Rod.stl 1 x...

Roulement 37X25X7 X2 becomes: Hello, Check out the V2 of my upgraded Spool Holder! It's bigger, stronger, and built to last, yet maintains the same level of modular positioning that you love. A game-changer for sure! ... 37x25x7 bearings - we've got...

No one knows anything about this person.

I printed this with Hatchbox 1.75mm PLA with a .08mm layer height and it needed no supports since I oriented everything standing up with the largest face on the build plate. ... V4 has finer threads on the shaft and taper which take forever to tighten...

Space saving spool mount for Anycubic Mega series of printers, Great for dual extruder setups you can mount a spool on each side, using four M3 screws and nuts / washers and a length of M8 all thread and nuts / washers per unit. ...UPDATED with a slide...

I'd like to give a big shoutout to the talented creator over at Thingiverse, who shared their amazing 3D model under an open-source license. ...You can check out the original design and all its awesome details on this link -...

I Require Additional Living Room Decorations

Customized version of https://www.thingiverse.com/thing:53451 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=53451

Customized version of https://www.thingiverse.com/thing:53451 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=53451

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

When the printer is placed in a low space room, the filament spool can be placed to the side and still be able to print to the max hight. ... For Ender 3 V2

When the printer is placed in a low space room, the filament spool can be placed to the side and still be able to print to the max hight. ...For Ender 3 V2

I printed mine with Hatchbox 1.75mm PLA filament, at .08mm Layer height, and no supports. Parts were oriented standing up with the largest face touching the build plate. For scaling, the hex face on the Cap should be 33.5mm.EDIT 1: I made some...

To improve aesthetics and give more firmness to the model, I remixed this great Spool Holder.I added holes for insert nuts and M3 screws.Insert nuts - M3 X D5.0 X L7.0 -->...

To close the printer in an acrylic case with minimal external elements while using the internal space effectively, this spool holder was created. The spool holder has a recessed area at the top where you can insert a small tube made of smooth...

... also needed. The holder is tailored for ColorFabb 750g spools but can easily be adapted to accommodate different spool sizes. ... For use with ColorFabb spools, a downloadable adapter model can be found here: http://www.thingiverse.com/thing:205957

Optimized Spool Holder Design: A Compact Solution for 3D Printing. No Additional Hardware or Supports Needed. This design uploads common sizes, ensuring a snug fit within its specified width. The STL file title clearly states the maximum spool...

The Anet A6 Space Saving Filament Spool Holder... the filament nestles snugly behind the top bar. I'm flying solo on this one, as it's my very first 3D print model. ...Unfortunately, I'm still a novice at creating smooth edges in SketchUp .

also got this idea from https://www.printables.com/@Leo_1098206. ...i however don't have or can't find a 2.5kg spool which his what his particular remix is for.5mm countersunk screws should fit fine.

We don't need another filament spool clip right now, but if we could print security, love, and understanding, that would be something worth printing. ...Together, we should be printing unity, not just holding our filament together with a clip.