nodemcu v3 3d models
25202 3d models found related to nodemcu v3.thingiverse
Remix for the RGB wave lamp base in order to fit the larger size ESP8266 Nodemcu v3.
prusaprinters
Design derived from https://www.printables.com/model/157431-nodemcu-v3-caseI liked the case plasmata designed, but needed more space beneath for easier pin access. ...This version provides more space and an unnecessary vent on the lid. </p>
thingiverse
This is a case for holding a NodeMCU v3 and 4x 7-segment MAX7219 8x8 led matrix. **NOTE**: The holes for the NodeMCU board are not properly aligned. The board fits but screws are a little angled. ...Will fix soon.
thingiverse
... Multisensor, thanks! ...This has been scaled larger to fit the NodeMCU v3 as the original model was too small. It also only has cutouts for the DHT22 sensor and ventilation. ...I don't use the other sensors so I removed the cutouts for them.
thingiverse
Required hardware - NodeMcu V3 - BME280 (Temperature, Pressure and Humidity sensor) - BH1750 (Light sensor) For inside the house PLA is good enough. If you want to use the sensors outside, use transparent PETG. ... Code:...
thingiverse
Simple case for NodeMcu v3 (LoLin). Inspired by the other cases, build from scratch. It has openings for the IO and the USB, as well as for the reset and flash buttons. Closes nice and tight - no need to add bolts or tape to keep it closed like...
thingiverse
Suitable for powering LED strips ~~up to about 1A.~~*, amperage depends on your power supply.* The NodeMCU v3 board is fixed into a larger compartment with four ~~self-tapping screws~~ *poles.* ~~The USB connector is exposed through a slot~~ *There...
prusaprinters
imported from thingiverse.remix: https://www.thingiverse.com/thing:4515152Enclosure for a NodeMCU v3 board with space for a connector to a strip of addressable LEDs. Powered via an external 5V USB<i>power</i> supply. Suitable for powering LED strips...
thingiverse
Esp2866 NodeMcu V3 Gehause housing Best ESP housing model of all time :)
thingiverse
A case for an ESP8266 NodeMCU V3 from AZdelivery with Relais.
thingiverse
3D printed cover for NodeMCU V3 board, PIR sensor and two LEDs for education purpose.
thingiverse
MySensors gateway box/case for nodeMCU v3 with hole for antena nrf24l01.
thingiverse
Suporte para ESP8266 Lolin NodeMCU V3 com furos 5mm para fixação em perfil 2020
thingiverse
NodeMCU v3 box with mount. ...Mount has screw holes without threads.
thingiverse
A remix of @jpersons NodeMCU v3 case to make it rack mountable.
thingiverse
... AM312, 5mm neopixel, TSL2561 -- though the fit is VERY tight with wires. Inspired by sensor box for NodeMCU v2: https://www.thingiverse.com/thing:2477685 Makes use of this support design for NodeMCU v3: https://www.thingiverse.com/thing:3334391
thingiverse
Requirements: 1 x 7-Bit WS2812 5050 RGB LED Ring Round 1 x nodemcu V3 3 x wires i couldnt get the orginal Mclighting to work very well, as it was my 1st time using visual studio code, therefore i used the below github project...
prusaprinters
just a stretched version fitting ESP8266 nodeMCU v3 from https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/samwiseg0/esp8266_nodemcu_din_mount by samwiseg0
thingiverse
Created an enclosure for the slightly larger NodeMCU, specifically this one: https://www.aliexpress.com/item/5PCS-V3-CH340-Wireless-module-NodeMcu-Lua-WIFI-Internet-of-Things-development-board-based-ESP8266-esp/32794607540.html My NodeMCU measures:...
thingiverse
Other models I found required the NodeMCU's PCB to have **rounded corners**. But mine has sharp corners, thus it did not fit there. So I created own model. Held together with 2.6 mm screws; NodeMCU's PCB is clamped in between. PartA is bottom...
thingiverse
ESP32 NodeMcu - Case (Lolin V3 no rounded corners) Designed this case because I did not like most of the designs out there. This one fixed all the issues and I'm happy with that hope other people enjoy as well. The lid holds into a grove and the...