nodemcu v3 case 3d models

Design derived from https://www.printables.com/model/157431-nodemcu-v3-caseI liked the case plasmata designed, but needed more space beneath for easier pin access. ...This version provides more space and an unnecessary vent on the lid.&nbsp;</p>

Remixing @jperson's NodeMCU v3 Case Design to Make It Rack Mountable

The device is housed within a NodeMCU V3 enclosure.

Simple case for NodeMcu v3 (LoLin). Inspired by the other cases, build from scratch. It has openings for the IO and the USB, as well as for the reset and flash buttons. Closes nice and tight - no need to add bolts or tape to keep it closed like...

Case for node MCU v3. Other models I found required the NodeMCU's PCB to have **rounded corners**. But mine has sharp corners, thus it did not fit there. So I created own model. Held together with 2.6 mm screws; NodeMCU's PCB is clamped in between....

Suitable for powering LED strips ~~up to about 1A.~~*, amperage depends on your power supply.* The NodeMCU v3 board is fixed into a larger compartment with four ~~self-tapping screws~~ *poles.* ~~The USB connector is exposed through a slot~~ *There...

imported from thingiverse.remix: https://www.thingiverse.com/thing:4515152Enclosure for a NodeMCU v3 board with space for a connector to a strip of addressable LEDs. Powered via an external 5V USB<i>power</i> supply. Suitable for powering LED strips...

I designed my own case because none caught my eye, so I decided to create something very minimalist with thinner walls to minimize print time and reduce material usage. A port is conveniently located on the bottom of the case for wire feed-through,...

I liked the case plasmata designed, but needed more space beneath for easier pin access. ...This version provides more space and an unnecessary vent on the lid. ***UPDATE: Added a base version with two holes for wire access.

The Simple Lolin ESP8266 NodeMCU V3 Case comes with the header and pins intact, leaving no modifications to be made. ...Printing at a scale of 101% yields an accurate representation of the case's dimensions, while printing the lid at 100% ensures a...

a simple ESP8266 case Designed for use with WLED firmware&nbsp;Assembly instructionPrint the caseSolder power and data pin to the NodeMCUpull the cable through the hole in the backput the MCU board into the bottom part of the caseput the lid onDone!

Needed a case and didn't find one I liked There is a port on the bottom of the case for wires to feed through as well as a clear port for usb cable connection. ... Added a simple cutout on top for better signal

<p>I wasn't entirely happy with other models, so I created my own.</p><ul><li>minimal size to protect all header pins</li><li>cutouts for USB port, the 2 buttons and Dupont connectors</li></ul><p>You just need 2x countersunk M3 screws or friction fit...

Simple Case for a v3 NodeMCU with or without an attached DHT22.

This case calls for housing a NodeMCU v3 and four 7-segment MAX7219 8x8 LED matrices.\r\n\r\n**Warning**: The holes for the NodeMCU board do not line up properly. Although the board fits, screws are slightly askew. ...Adjustment will be made soon.

Required hardware was as follows: - NodeMcu V3 - BME280 (Temperature, Pressure and Humidity sensor) - BH1750 (Light sensor) For inside the house, PLA was good enough. If you want to use the sensors outside, transparent PETG should be used. ... Code is...

... to this. ...The top, bottom and an accent colour board (for some extra fun).The design doesn't serve too much of a practical purpose (the hexagons look cool) but, the pins are recessed into the case to prevent them from being accidentally bent.&nbsp;

Get this design at https://www.treatstock.com/3d-printable-models/2684254-sleek-nodemcu-case ### Enhanced Version of NodeMCU Top Case I was driven to remix this outstanding case to make the NodeMCU appear more streamlined and discreet. ... What it does:...

Simple box for status display device which is using : - Waveshare 4.3" UART e-ink display (waveshare.com/4.3inch-e-paper.htm)- Lolin Nodemcu v3

Simple box for status display device which is using Waveshare 4.3" UART e-ink display (https://www.waveshare.com/4.3inch-e-paper.htm) - Lolin Nodemcu v3 You can check my other designs [here](https://www.thingiverse.com/tmseth/designs/) Leave a...

Work in progress

Modification of my previous design now optimized for seamless integration with the latest nodeMCU v3 module. This updated version is specifically designed to work in tandem with the same compact mini power supply unit (PSU). ...Please note that this...

Das ist ein Case passt für einen NodeMcu mit ESP8266-12F in der Ausführung V3. Das Case gibt es in zwei Ausführungen und mit zwei verschiedenen Deckel. Benötigt werden für die Montage noch 6stk Schrauben M3x10 Ideal für Led Stripes / Ambilight...

The NodeMCU V3 box comes equipped with a mount that features screw holes which unfortunately lack threaded counterparts.

Just a Test for NodeMCU (Lolin) and a Bosch BME280 Clone. ... This Project can be found on my website at https://technikmensch.com/node-mcu-gehause-3d-printer-stl/.

Remix of a [remix](https://www.thingiverse.com/thing:3069030). ...I added a cutout to the bottom part of the case so that wires can go through it.

Case designed specifically for the NodeMCU V3 board, featuring a conveniently located micro USB port for effortless connectivity and recharging.

MySensor NodeMCU V3 Gateway Box/Case Features a Notch for NRF24L01 Antenna.

... can create a wide range of applications, from smart home automation to industrial control systems. The NodeMcu V3's compact design and ease of use make it an excellent choice for those looking to build innovative solutions with Wi-Fi connectivity.

UPDATE: In response to user requests, I've added an alternative top case with elevated walls (Refer to comments). This modification not only improves the overall design but also provides additional protection for the pins within the enclosure. I...