nodemcu v3 case 3d models

Custom Enclosure for the EsPixelStick with Integrated Fuse Hole and 5.5x2.1 Power Adapter Compatibility, Plus Solderless Cable Support and Level Shifting Capabilities

This is a Remix of https://www.thingiverse.com/thing:2408514

= Designed by SeanChang =●Thingiverse(Get The STL File): https://www.thingiverse.com/thing:4707566

<p>Supports needed.</p>

I remixed techniczny's case to fit perfectly with my specific AZDelivery NodeMCU Lua Amica Modul V2 ESP8266 ESP-12F module and 5V AZDelivery 2-relay module with optocoupler low-level-trigger. I used the following components: * Nodemcu: AZDelivery...

This was made to host a NodeMCU and a small IPS LCD ST7789. ...It has enough space for cabling some sensors and some holes for output cables. Was made for measuring temp and humiditiy in my DIY 3D printer case.

NodeMCU Case with Keychain Hole Addon Base Layer Settings: Print Method: Boltz Megatiete XY Raft Options: Enable Rafts Support Material: Enable Supports Layer Resolution: 0.05 to 0.1 mm Infill Density: 40% to 60%

The LCD Display and NodeMCU are securely fastened to the case using M3 (3 mm) screws, which are spaced out by four spacers for each component. The LCD Display is positioned at the bottom of the enclosure, while the NodeMCU ESP8266 Board is mounted...

Designed this case for my NodeMCU 1.0 ESP-12F ESP8266 board. Ordered a bunch of those from AliExpress (e.g. https://www.aliexpress.com/item/1005001621705950.html) and needed a case to fit them. Case provides access at the front side to micro USB...

Features: Nodemcu and double channel relay fit into case. Mounting of pcb's with holes for 3x8 and 3x10 machine screws. current version needs spacer, which will be corrected in next update. Holes for micro usb power supply and relay cables. Relay...

A compact housing solution specifically crafted for boards equipped with the NodeMCU microcontroller and featuring a high-resolution 1.3-inch OLED screen integrated directly into the design. This enclosure eschews traditional screw-based assembly...

On the next two photos, you'll see the integration of an Arduino Nano with my Ambilight laptop setup and on the last two, a Lolin NodeMCU paired with my AmbiPiBox case designed for Odroid's and Raspberry's. This case also serves as a single...

Use M3 screws to secure the board into the case 3 wires for Vin (red, no more then 5V) Ground (Black) And data (D4) (Green) Wire the +/- in series with the LED strip and green goes to data. ... https://install.wled.me to load the sketch on the NodeMCU...

Improved version of ESP8266 NodeMcu v2 (1.0) DHT22 Case with enhanced temperature accuracy. The upgraded design features a significantly reduced error margin, now just about 1 degree Celsius at 20 degrees Celsius compared to the original's 7-degree...

Quick and very dirty modification of NodeMCU base to fit a Wemos D1 Mini.

This is a case for a ST7735 TFT display including the cable connector, and an Arduino Nano or SBC-NodeMCU board. The display as well as the MCU board can be put in place without screws or glue. There's space for several components: * A DHT22...

Case with sliding lid for PixelBlaze v3

Wanted some fance enclosure for my PC monitor :) This rocket looks good :) There is space for nodemcu or arduino inside.

This is a versatile wall mount enclosure specifically designed for an ESP8266 NodeMCU, complete with a built-in 1x DHT22 temperature/humidity sensor module. The case consists of two distinct parts: a lower base that features four screw options for...

Designed this case for my NodeMCU 1.0 ESP-12F ESP8266 board. Ordered a bunch of those from AliExpress (e.g. https://www.aliexpress.com/item/1005001621705950.html) and needed a case to fit them. Case provides access at the front side to micro USB...

v3

This is a case for the DOIT.am brand motor driver shield for the NodeMCU dev board, where 3m double-sided tape will be used to secure the board to the bottom. A single wall thickness on the terminal strip side is meant to be cut out but should...

This is a compact setup featuring a single NodeMCU board paired with a TFT screen of the ILI9341 type. Three distinct components are required for assembly. ...The weather station's programming is courtesy of the team at GitHub, specifically squix78.

... side. Here are the ESP8266 boards I used: I purchased these ESP8266 boards from AliExpress: New Wireless module CH340 NodeMcu V3 ESP8266 ($2.38) You can also find them on Amazon for $10.49 - 2pcs NodeMcu Lua V3 Development Board ESP-12E CH340G

This case contains an Amica nodemcu v2, a 0.96" OLED display, and a BME280 sensor. The BME280 is inserted into a pocket that can be easily sealed with elastic gum to minimize its impact from the controller's warmth. The rest of the components are...

This case houses a nodemcu v2 'Amica', a 0.96" OLED display and a BME280 sensor. The latter gets slipped into a pocket which is easy to seal off with a little elastic gum so the measurements are a bit less influenced by the controler's warmth. Adding...

v3 of the case for my RS485 to WiFi adaptor

TMS320-XDS100-V3 Case. ...Requires 4 screws 2.6x7mm

This case houses a nodemcu v2 'Amica', a 0.96" OLED display and a BME280 sensor. The latter gets slipped into a pocket which is easy to seal off with a little elastic gum so the measurements are a bit less influenced by the controler's warmth. Adding...

This case houses a nodemcu v2 'Amica', a 0.96" OLED display and a BME280 sensor. The latter gets slipped into a pocket which is easy to seal off with a little elastic gum so the measurements are a bit less influenced by the controler's warmth. Adding...