note 2 phone 3d models

Since pankajbokdia asked nicely in the post of:http://www.thingiverse.com/thing:164281 I've decided to share my base models I use to make cases for my phone, there are 4 base skin models with different thickness. For my UP Plus Pro printer I use a...

A stand that I made for my phone. ... (Samsung Galaxy Note 2)

Just a mobile phone holder for "Meizu M2 Note", designed to be install in car heater vent grill. ...Designed special for Saab 9000.

Couple variations on a case I made for a Galaxy Note 2.

The Goonies - Chunk Truffle Shuffle, Galaxy Note 2 Phone Case

I recommend you to print this case with Flexible ABS

Customized version of http://www.thingiverse.com/thing:526257 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=526257 Instructions Using the following options: slots =...

Team Down Town is my airsoft team in Busan, Korea.If you want, I could put your initial :)

Edited With blender added Ingress Enlightened Logo

This is a Galaxy Note 2 Smartphone Holder and Stand. ...It has a gap for charging cord and can be wall or base mounted.

http://www.thingiverse.com/apps/customizer/run?thing_id=1665478 Instructions Using the following options: clamp_gap = 0.5 clamp_rotation = 0 bracket_small_ends = 5 clamp_angle2 = 30 clamp_angle1 = 20 thickness = 2.5 smartphone_thickness = 8.41...

2-part phone case designed for the Xiaomi Redmi Note 8 as part of a project in school, as such the square cut-out on the outer shell of the case design is present, but can be filled in with either of the parts, depending on which you think will look...

Sorta did a remix of the phone holder but made it for the Samsung Note 2. yes, i still use that phone.... I sorta did a remix but not really at the same time, I redid the part on solidworks as thats what I have and use to using. Also included the...

I made this for my Galaxy Note 2 which has a pretty thick rubber case. Because of this, the cradle may be a bit deep for most normal sized phones. While it may not be a snug ft for most phones, it should still hold most them suitably enough. ... ...

For KickStarter Micro Phone Lens: Cell Phone Based Microscope, by Thomas Larsonhttps://www.kickstarter.com/projects/968523355/micro-phone-lens-cell-phone-based-microscope Note lens hole is too small for my lens. Needed some file work. Customized...

http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options: phone_thickness = 12 phone_width = 80 offset = 0 support = 0 connector_depth = 6 connector_height = 15 connector_width = 9.8 TextLabel = ALİ...

its a note 2 phone case with dota 2 icon cut out. i have problems with flex pla it just sticks to heat bed and wont comeout dunno why if anyone has an idea feel free to share =) Instructions i made...

http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options: connector_depth = 6 phone_depth = 3 connector_width = 9.7 phone_name = Samsung Note 2 phone_width = 80 extraD = 0 font_size = 11 support = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options: font_size = 10 TextLabel = Note 2 phone_depth = 6 phone_width = 81 connector_width = 10.2 connector_height = 19.1 connector_depth = 7 phone_name...

Samsung Note 2

Music Note Phone holder. this will hold any phone on it. ...This item prints in 2 separate pieces.

A Phone Holder for a Samsung Galaxy A5 on a music note

Phone holder for Nissan Note Will clip onto the storage room in the center of the dashboard. ... Will fit a phone in a flipcase.

This is a note 9, 3d printable case to fit, my not be exact due to curves of the phone

Here is a phone stand i made for my Note 5. It is inspired by those library chairs with multiple tilt angles. It also has two vertical angles 10* and 25* degrees. The inside dimensions are 10mm by 80mm so your phone sould be <10mm thicc and <80mm...

Simple Design of a phone

This is a modified end for a wall mounted phone holder to hold a Samsung Galaxy Note 9 in a Spigen Tough Armor case. I printed in PETG for extra strength but you do it how ever you want. It is a little big to help accommodate a thicker case so it...

This is a modified end for a wall mounted phone holder to hold a Samsung Galaxy Note 9 in a Spigen Tough Armor case. I printed in PETG for extra strength but you do it how ever you want. It is a little big to help accommodate a thicker case so it...

Note 4 holder in your mercedes-benz w202

Galaxy Note 2 Phone Holder for CTC 3D Printer and kompatible. Print out this holder 2x and mount your Galaxy Note 2 in front of your CTC 3D Printer to use them as a webcam. I use the following App: ...