note4 3d models
44 3d models found related to note4.thingiverse
Customized version of http://www.thingiverse.com/thing:1665478 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1665478 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1665478 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1665478 Instructions Using the following options:...
thingiverse
This is a project to create a Samsung Galaxy Note 4 model for use in cases holders etc. At the end of it I want to end up with 3 files. Top and bottom shells for a negative and a phone model with enlarged sections to leave space for access to buttons...
thingiverse
This is a cradle to hold a Samsung Note4 (no case) and snaps into the TTVR modular virtual reality heasdset (http://www.thingiverse.com/thing:733390). It is very important that the corners not lift during print since the dimensions are precise and...
prusaprinters
This is a cradle to hold a Samsung Note4 (no case) and snaps into the TTVR modular virtual reality heasdset (http://www.thingiverse.com/thing:733390). It is very important that the corners not lift during print since the dimensions are precise and...
thingiverse
Does not work with a bare Note4 - is specifically designed to fit the Otter Box enclosure for the phone. Instructions No need for [additional] supports. I printed at 0.25mm Z height with a 0.4mm...
thingiverse
Adaption of ID 423146 to correct the lens focus range Print Settings Printer: CTC Rafts: No ...
thingiverse
Customized version of http://www.thingiverse.com/thing:526257 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=526257 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1655546 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options:...
thingiverse
Un pequeño soporte para poner mi note 4 mientras hago rodillo en la bici...
thingiverse
This is a remix of Cort's mobile phone holder, basically just resized to perfectly fit a Samsung Galaxy Note4 sporting the original Samsung-manufactured phone case. ... I have also split the orignal model into two separate STL files for easier...
thingiverse
Customized version of http://www.thingiverse.com/thing:1655546 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options:...
thingiverse
OpenGear is a Virtual Reality headset which emulates the Samsung GearVR headtracker. It is an open source project, with the firmware and STL files openly available. http://www.Open-Gear.com ...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6w2CId9MSaE
thingiverse
Customized version of http://www.thingiverse.com/thing:932425 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=932425 Instructions Using the following options:...
thingiverse
this is an android version of "Tesla Iphone Supercharger by runeloken". i have modified the red inlay to fit a USBmicro cable end. i have also added a pass thru so that an led can be installed in the top. i used 2 red leds and a 300 ohm resistor. it...
thingiverse
Hi This is my own design project which acutally for my cafe POS mobile phone (Galaxy note4) I used 3dsmax for modeling process.
thingiverse
Just another Stand/Holder for a Samsung Note4. In the back its having a guide for the USB Cable. ...Hope you enjoy it!
thingiverse
This adapts your small note4 stylus to a much larger and more ergonomic size, similar to a wacom stylus. ... You must print at high quality as the tolerances are tight.
thingiverse
Here is a stand for the Note4. I made it to work with my Samsung case. For the inductive charger I bought this Wireless Charger,Itian®Qi Wireless Charging Pad K8 on Amazon for $10.http://amzn.com/B00V2PB16O Pull it open and hot glue it to the...
thingiverse
... I figured I wanted to be able to put my phone in portrait as well... so here is a tweak! As per the original - download the scad file (unless you have a Note4 with a gell case!) and tweak the variables at the top of the file to suit your device.
thingiverse
... whether you find the serving sizes correct or not. NOTE2: It might print better up-side-down since the text has less overhang then. NOTE3: I corrected the labels, before the I & II were mixed up. NOTE4: Dimensions has been updated 2014-09-13
thingiverse
2) TTVRCradle - either Note4Bare(Note4, no case) or Note4OB (Note4 with an Otterbox enclosure). 3) LensmmX2 - you will need a pair of lens holders to fit the lenses chosen. No supports or brim required. 4) clips - a complete set of clips required...
thingiverse
... into the Mavic shoulder bag. Included are parts to fit iPhone 6 & 7, iPhone 6 & 7 plus and Samsung Note4. The parts named "base", "sideL" and "sideR" are the same for all models. ...Only "back" and "top" are customized according to the phone model.