npt to garden hose adapter 3d models
2175700 3d models found related to npt to garden hose adapter.thingiverse
I found STEP files for a 3/4" NPT coupling and male garden hose fitting and generated a printable transition between them to make this design. This is being used to take the water from my evaporative air conditioner pump-out and put it on one of...
thingiverse
Quick and dirty NPT to quick release garden hose adapter. ... Print with 4-5 perimeter layers, 50%-70% infill.
thingiverse
Needed a sump pump adapter so I could connect it to my garden hose. Going to experiment with this. ...Not sure if it'll be sturdy enough but will see
thingiverse
I am using this in my RV to adapt the exterior shower hose to a garden hose so that I can hook up an outdoor Fillet Table that has a sink and faucet. ...Cost: $0.48 Print Settings Printer Brand: RepRap ...
thingiverse
Adaptor for the shower head to a garden hose, npt type.
thingiverse
Remixed this from this design and also this design and also a Female pipe thread design to connect a garden hose onto a water pump that I have that is Male NPT Female Pipe Thread Design I Remixed With: https://www.thingiverse.com/thing:4908168...
thingiverse
1 1/2" npt to garden hose adapter with a cone shape inside for extra strength. ...I used it to connect a temporary sump pump to a garden hose.
thingiverse
A simple male 1" NPT to garden hose adapter (GHT) for a sump/utility pump. ... Works well when printed in PETG and at a finer layer size (I printed mine at 0.01mm and it's water tight).
thingiverse
Used the threaded part for the male garden hose to make a 3/8npt male to garden hose male adaptor for my 12vdc sprayer pump. I also have the female end made as well. ...
prusaprinters
Used the threaded part for the male garden hose to make a 3/8npt male to garden hose male adaptor for my 12vdc sprayer pump. I also have the female end made as well.</p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>Anet A8</p> <p...
thingiverse
Made an adapter for my sprayer pump. ...3/8npt to Garden hose.
thingiverse
... hose. The portable water source I found was a Home Depot sprayer. The thread is Male Garden hose, to 1/4 NPT with a tube barb, just like the wand. ...Took me a few prints to get the size right, then add the barb, but now Works like a champ!
thingiverse
I needed to drain my irrigation system and I have access to a spout that's a male garden hose thread (3/4 BSP) and adapted an air hose end to make this easy. Please see verify your system to see how much PSI you can run through it. ... I ran each...
thingiverse
Designed to interface a garden hose to a valve. Use plenty of teflon tape or it may leak! ...If you can smooth out the inside surface, you can use a hose gasket, which helps a lot!
thingiverse
I was fixing my bidet and wanted to attach it to my garden hose. ... I wanted to fix it in the backyard where it's easier to work on.
prusaprinters
3/8npt to Garden hose. Print Settings Printer: Anet a8 Rafts: Yes Supports: No Resolution: 0.2 Infill: 100% Notes: Printed in petg with a full brim. Does not need supports. Printed at 235c with no fan. How I Designed This =================== I...
thingiverse
garden hose to 40mm drain pipe. ... garden hose connection to rinse a 40 mm drain pipe. ... fits almost all quick connect garden hoses.
thingiverse
This is a garden hose to pinlock adapter for use in home brewing or whatever you would like to do with it. ...:)
thingiverse
Adapter to switch from 20mm garden hose to filter pump hose. 32mm. Useful for small pools that do not have an outlet for a filter pump but for drainage. You can use this outlet to connect the filter pump. I have printed this piece with PLA, but it...
thingiverse
This was a combination of two items from Thingiverse: https://www.thingiverse.com/thing:551238 and https://www.thingiverse.com/thing:10189 The garden hose threads fit nicely on a real hose, and they can be printed without support at 0.2mm layer...
thingiverse
Made an adapter for my dehumidifier to go into the condensate pump.
thingiverse
... ... This is an adpater that will allow you use to connect a water hose to the faucet. It can be customized for whatever project needed. For the time being it, is a work in progress. It is a pretty heavy customization of the nuts and bolts openscad.
thingiverse
Remixed this to be a bit longer from https://www.thingiverse.com/thing:219625
thingiverse
I made this Guillemin coupling to Gardena garden hose coupling adapter at work. This allows me to connect a garden hose with quick lock connector to a fire hydrant with what is apparently called a Guillemin connector. This is a two part design which...
thingiverse
needed an 1-1/4 inch npt output, designed this, printed it, was pretty tight fit, i'm printing now at 98% to see if it works better, although the original version is on the pump right now and is functioning. print horizontally with supports. ...petg...
prusaprinters
The barbs on mine hold so well I needed to cut the hose off to take it apart.I can't comment on the amount of pressure this can take, use at your own risk.Printing:I printed it as it sits in the file with the smaller end as first layer, with supports...