nut driver holder 3d models
462835 3d models found related to nut driver holder.thingiverse
i was looking for a holder for my 1/4" shank nut drivers and bit that i could mount to my wall or tool cart and i could not find any that i liked. so i just made some. i have printed 2 of the smallest holder and they have both printed great. ... no...
thingiverse
Holder for the DYN DYN2806 Dynamite 5 pc Metric Nut Driver Assortment you can get on Amazon. I found a few different versions but they were too big and bulky or didn't look like they would hold the drivers straight. I wanted something pretty solid...
thingiverse
Keep all of your nut drivers together, instead of mixed up in a sloppy drawer. Made with TPU, a rubbery filament. ...
thingiverse
A Basic Bondhus Allen Key and Nut Driver Tool Holder for Prusa Ikea Platsa Enclosure
thingiverse
Holder for the Husky SAE set of 7 nut drivers from Home Depot. ... Prints in two halves.
thingiverse
Customized version of https://www.thingiverse.com/thing:537516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=537516
thingiverse
Customized version of https://www.thingiverse.com/thing:537516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=537516
thingiverse
Customized version of http://www.thingiverse.com/thing:537516 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=537516
thingiverse
Just a basic Allen Keys and Nut Drivers holder for the IKEA Platsa cabinet. ... Allen Key Drivers: https://www.ebay.com.au/sch/i.html?_from=R40&_trksid=m570.l1313&_nkw=Black+Long+Hex+Allen+Key+Socket+Bit+Set+Hex&_sacat=0 Nut Drivers:...
thingiverse
Customized version of https://www.thingiverse.com/thing:537516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=537516
thingiverse
I purchased a small kit of four nut driver bits, but it didn't come with a way to store them. ... Rather than just having the bits lose on my bench--where they WILL get lost--I pulled out Fusion 360 and my calipers to build a simple box to store them.
thingiverse
Due to the exact measurements required to get the magnets to make contact with the metal of the nut drivers, I'm not sure if this exact design will be of any use to others. I am putting it up here so someone else might benefit from and improve upon...
thingiverse
Fits Drillpro 14 piece 1/4" hex nut driver set (7 metric, 7 SAE). ...Designed to take up less space in the toolbox and much easier to get the drivers out over the original crappy rubber holder.
thingiverse
Customized version of https://www.thingiverse.com/thing:3808539 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3808539
prusaprinters
My nut driver sets have the following shaft sizes: Metric : 10mm, 7.7mm, 7mm, 7mm, 7mm, 5.85mm, 5.85mm Craftsman : 0.435", 0.435", 0.313", 0.313", 0.313", 0.246", 0.246" Each holder consists of a main section with insertable pegboard hangers. ...Each...
thingiverse
This little holder supports x20 Xcelite mini nut drivers. Specifically, the PS-120 (imperial) and PS-121mm (metric) sets. The design allows for all size printing on the drivers to be seen at a quick glance while keeping bench space to a minimum. ...
thingiverse
Customized version of http://www.thingiverse.com/thing:537516 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=537516
thingiverse
A simple design to hold the SAE and Metric sets of nut drivers / setter. Specifically designed for the Harbor Freight Hercules sets but may work for others. ... Parts numbers: Metric: 64787 Model: HA22-53 SAE: 64767 Model: HA22-54
thingiverse
This holder was designed with wider spacing than my other standard 3 Piece Holder to hold a 5/16 and a 3/8 Nutsetter bit along with 1x Driver bit as shown in photos This holder is able to hold the same 3 Piece Socket adapter kit as my Makita version...
thingiverse
A clip designed to hold a flanged hex screw in an impact driver bit. 99% of the time you probably would not find this useful. But for that 1%... I needed to install Stainless steel (non-magnetic) self drilling screws into aluminum in a very...
thingiverse
I want to have all my tools neatly available. This was designed to fit my Biltema Pegboard that has a 12x12 mm grid Tip. ...This tool set is a must for any Pinball hobbyist ;)
thingiverse
Nut driver holder SAE: 1/4, 5/16, 11/32, 3/8, 7/16, 1/2 Metric: 6, 8, 9, 10, 11, 12 10 bit holder Made for the extra bits from a Husky 149pc mechanics tool set If the holes are too snug use a 7.5mm or 5/16" drill bit
thingiverse
This is a simple M3 nut driver/holder. It can get into tight spaces and give you good grip. Use DAE file or scale STL by 25.4. It MUST be printed with brim. I do not recommend flipping it over. ... 210C, 30MM/s Print, 50MM/s Travel (Important)
thingiverse
... was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/8WjXCVqTg8z. I remix the clip.stl from https://www.thingiverse.com/thing:2365190) by lengyej to use it as a net driver for the phone mount. ...Thank lenqyej for the design.