nzxt h500 case mod 3d models

Mini NZXT h500 case for raspberry pi model 4 Video Link: https://youtu.be/3GUH698xS0k

This is designed for a NZXT H500 case but might fit other cases or could be scaled up or down to make it fit. (make sure you don't block the cooling of your case) The front is 436mm by 211mm. EDIT: I added the Fusion 360 file for anyone who...

Good news everyone, I have made a custom covers for SSD in NZXT PC cases. I can provide data for clipping for any other design in any CAD format. Enjoy! SSD_Cover_Base. Can be just as a cover. Those with division are just two similar...

The feet fit the rubber part of my H500 case, please measure yours and adjust the 3D file if the measurements don't match, or if you think your 3D printer needs different margins. I've heard that there are different dimensions for the rubber parts...

This is a MOD for my case NZXT for better air flow. You can do the same if you like. You just need to cut the front panel for 38.5 x 14.5 and print the files. I have done all of this on my Ender 3, the Hoop had to divide by 3 to be able to...

This is an ATX cable mount for the NZXT H500 PC case. Prints in 3 pieces, combs must print "flat" for durability. The flat "sticks" on the left and right pieces lock into corresponding the lip on the opposite piece. I used a bit of SuperGlue (the gel...

After cleaning the bottom filter for my rig, I realized I needed risers to get it off the carpet. The fans were pulling quite a bit of dust and pet fur into the lower filter. I whipped up a quick and dirty model for risers that allow for the PC to...

This is a hard drive mount for an my NZXT H500. It was intended to reduce vibration and noise of my hard drive, but didn't work out so well for that. Uploaded anyway. ...Perhaps someone can use it.

Things needed post printing: 3mm acrylic sheet 1/2 magnets Gel super glue Screws with washers acrylic cutting tool i used the original mounting points for the front panel to attach the new mounts

***Updates*** - 2020-11-23 - added `nzxt-140-mesh-circle-v2.stl` new version with round holes matching original design ***NZXT back replacement*** Replacement for backpanel with mounting for 2 140mm fans ***Mounting ball*** This are for being able to...

A Remix of NZXT H1 lcd Panel for the 4 inch HDMI IPS Touchscreen 800 * 480 on Amazon LCD Panel https://www.amazon.de/Waveshare-4inch-LCD-HDMI-Resolution/dp/B07QK89X53?ref_=ast_sto_dp&th=1&psc=1 HDMI Cable...

This is a remix of https://www.thingiverse.com/thing:4883292 to allow it to fit in the front of NZXT H1. The pins are for the bottom of the 3d prints and will hold for the front. The new files have cut outs to fit. ...

... I just used hot glue to secure the display to the mount. DO NOT put hot glue along the bottom edge, as this will create interference with the mount on the case.

SSD Bracket to add more hard drives to a NZXT M59 Case. You will need to print x2 Brackets and 4 screws per SSD/HDD. ... The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket.

SSD Bracket to add more hard drives to a NZXT M59 Case. ...You will need to print x2 Brackets and 4 screws per SSD/HDD.</p> <p>The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket.</p>...

Similar to my EKWB pump / res combo holder: https://www.printables.com/model/291904-ek-pump-holder-for-nzxt-casesThis mounts the Alphacool Eisstation to the vertical bar inside NZXT's PC cases.

Inspired by some of the LCD mods on Reddit/SFFPC for the NZXT, I gave this LCD mod a crack and it worked out pretty well.You need the 3 prints.. ...one's the back plate, and two brackets to hold the screen in place.</p><p>The screen i used was this...

NZXT Case for Raspberry Pi. Will fit more other Pi's but check. Top is glued on. Rings are pressed in, very tight. Perhaps print them 99% in all dimensions. Bar is also pretty tight. ... Snaps in.

# ## Italiano: ## Questo logo é all'interno di tutti i computer di NZXT. Esso ha una dimensione standard e quindi é adatto a tutti i case. Dimensioni: Larghezza 85mm Altezza 22mm Qualsiasi commento o suggerimento è ben accetto. ## English:...

This is a replacement spring latch for an NZXT Phantom computer case. Mine broke and it's not likely that I can get spare parts for this old computer case. It was modeled in Fusion 360 and I printed on my Prusa Mini. It is a bear to install this for...

Blank mini NZXT case design I have created. Change size of model to at least 150% in your slicer for recommended detail. Size larger then 150% will also work. Must Print with supports inside for pipes to print properly. ...Removing supports between...

This is to allow everything to fit on the bed and account for tolerance issues.&nbsp;Printed with Protopasta CF-HTPLA w/ a 0.4mm nozzle, 10% gyroid infill, 4 perimeters, no supportsFor retaining pins on case, requires M3 brass inserts and M3x10...

Made because my case had rubber nubs that sunk into my carpet and my intake fans couldn't cool anymore! Over all I saw a 10 degree cooler pc! This was under normal load so the temperatures will vary for you. I'd strongly recommend printing one before...

This is a stand for NZXT H510 case

this is a mount for the corsair commander controller. ...it is designed to fit the ssd mount in the nzxt H510i case.

This is a 5.25/optical bay cover for an old 2004-era NZXT PC Case. I got the case 2nd hand, and wanted to fill up the empty bays for dust and airflow reasons. ...Enjoy.

I printed one of these nzxt h440 headphone holders and it did no fit my case so i designed my own my case front is 16mm thick at the top where the holder fits

I needed my existing 14TB HGST hard drive mounted inside the NZXT H1v2 case, however the screw holes on h1v2 does not match the ones on hdd. I don't want to drill holes. Inspired by [thing:4622587](https://www.thingiverse.com/thing:4622587), I...

LED strip mount for NZXT 510 flow case. Might work with their other cases too but not sure. I used glue to attach the led strip to the mount but could also use double sided tape. ...This replaces the parts in the case where the glass snaps into just...

Modified the original controller hook to slide right onto the front of NZXT's S340 PC case, should hold any Xbox/Playstation controller. ... I recommend making the entire hook skinnier/wider based on the controller you use, to make it harder for the...