nzxt phantom case mods 3d models

This replacement spring latch is designed specifically for NZXT Phantom computer cases, but mine snapped and spare parts are unlikely to be available. The part was created using Fusion 360 software and printed on a Prusa Mini 3D printer. ...Installing...

A custom-built truss system designed to support a NZXT Phantom case, preventing it from drawing in carpet dust and debris consistently. ...Each corner requires a sturdy truss to provide optimal stability and protection.

The NZXT PC Tower includes a Phantom model, crafted as a single unit with a closed small door feature. ...However, this design lacks an E-SATA port on its front panel.

This is an adapter to fit a 140mm fan in the 200mm slot in the top of the NZXT Phantom Case. ...I was unable to find a 200mm fan that would fit the top of the case so I created and printed this adapter.

The rubber USB port cover flap on top of my NZXT Phantom 820 began to break down and I've always found it dull and unattractive. This replacement sits slightly recessed into the case, offering a sleeker alternative. The clear TPU looks very appealing...

The rubber USB port cover (flap) on the top of my NZXT Phantom 820 was starting to disintegrate and I've always found it boring/ugly. This is a replacement that sits slightly recessed into the case. The clear TPU looks pretty nice and doesn't slide...

The rubber USB port cover (flap) on the top of my NZXT Phantom 820 was starting to disintegrate and I've always found it boring/ugly. This is a replacement that sits slightly recessed into the case. The clear TPU looks pretty nice and doesn't slide...

Hey everyone, I've created a custom modification for my NZXT case that enhances airflow. If you're interested in making the same upgrade, feel free to follow along. To get started, simply cut out a panel with dimensions of 38.5 x 14.5 and print the...

Replacement part for USB 3.O Hub in NZXT Phantom 410 Series Computer Case

A 3D printed adapter for Cooler Master MF200 fans to be installed in the OG NZXT Phantom. Printed in PLA with 100% infill. ... Not perfect, required some massaging to get all 4 holes to line up, luckily the MF200 is a bit flexible.

SSD Bracket to add more hard drives to a NZXT M59 Case. You will need to print x2 Brackets and 4 screws per SSD/HDD. ... The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket.

SSD Bracket to add more hard drives to a NZXT M59 Case. ...You will need to print x2 Brackets and 4 screws per SSD/HDD.</p> <p>The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket.</p>...

Similar to my EKWB pump / res combo holder: https://www.printables.com/model/291904-ek-pump-holder-for-nzxt-casesThis mounts the Alphacool Eisstation to the vertical bar inside NZXT's PC cases.

Made a small hook, to place my cords on the side of the case.Its designed for the holes in the NZXT H710 Case.

NZXT Case for Raspberry Pi. Will fit more other Pi's but check. Top is glued on. Rings are pressed in, very tight. Perhaps print them 99% in all dimensions. Bar is also pretty tight. ... Snaps in.

# ## Italiano: ## Questo logo é all'interno di tutti i computer di NZXT. Esso ha una dimensione standard e quindi é adatto a tutti i case. Dimensioni: Larghezza 85mm Altezza 22mm Qualsiasi commento o suggerimento è ben accetto. ## English:...

Blank mini NZXT case design I have created. Change size of model to at least 150% in your slicer for recommended detail. Size larger then 150% will also work. Must Print with supports inside for pipes to print properly. ...Removing supports between...

Considering temperature variations will occur depending on individual cases, I strongly suggest printing one before making all four to ensure a snug fit. If your rubber feet are slightly oversized like mine, you may want to upscale the model by...

Things Required After Printing: * 3mm Acrylic Sheets * 1/2-Inch Magnets * Gel Super Glue * Screws with Washers * Acrylic Cutting Tools I Utilized the Original Mounting Points on the Front Panel to Attach the New Mounts.

This is a stand for NZXT H510 case

ESP01D1 CASE Phantom V1

ESP01D1 CASE Phantom V2

this is a mount for the corsair commander controller. ...it is designed to fit the ssd mount in the nzxt H510i case.

This is a 5.25/optical bay cover for an old 2004-era NZXT PC Case. I got the case 2nd hand, and wanted to fill up the empty bays for dust and airflow reasons. ...Enjoy.

LED strip mount for NZXT 510 flow case. Might work with their other cases too but not sure. I used glue to attach the led strip to the mount but could also use double sided tape. ...This replaces the parts in the case where the glass snaps into just...

Modified the original controller hook to slide right onto the front of NZXT's S340 PC case, should hold any Xbox/Playstation controller. ... I recommend making the entire hook skinnier/wider based on the controller you use, to make it harder for the...

I attempted to print one of those NZXT H440 headphone holders, but it didn't fit my case perfectly. I decided to take matters into my own hands and design a custom solution that would work seamlessly with my setup. ...The front of my case is 16mm thick...

This holder ist designed for the NZXT Case, because there is a hole in its "bottom" where the holder can fit in. On its top, of the holder, it just has contact to the 2x8pin connectors. ...The version I uploaded is slightly different, I fixed some...