octopi wifi camera case for b 3d models

This design was created to upgrade the A10, A10M, and now also fitted it to my CR-10sPro and basically every printer when using the no attachment case, with the power relay feature to switch on/off the printer:...

added some height to the case to allow for heatsink as not tested but old case would make it very close to the lid based on the stock heatsink you can buy, for the lid i made some holes where the heatsink should be so it can vent. ...Also changed bottom...

Hardware Used: 4x M3x8 hex socket CAP head screws for main case mounting 2x M3x16 hex socket BUTTON head screws and nuts for swivel mechanism assembly 2x M3x8 HEX head screws and T-nuts for aluminum profiles Big thanks to michaelvs for his...

PCB holder with lid for mini P1 a slimme meter WiFi gateway, specific for the SMR5 meters. ...The PCB is developed by Henri.More information about corresponding PCB.

I printed a custom case designed specifically for the Raspberry Pi, featuring the same original 7-inch LCD screen. This system was built to work seamlessly with the OctoPrint print server. ...Using pet-g material, I achieved a 15% fill rate to optimize...

This is a simple small case for a CellSol WiFi Pylon built using the recommended Heltec LoRa32 or V2 board. This has room for a small LiPo battery, the LoRa32, and your antenna mount, and has a port for USB. Using silicone gasket material, silicone...

This is a case for my external camera timelapse controller. It holds two ESP*266 Nodemcu devices and a micro USB breakout board. One of the ESP8266s connects to your local WiFi and then to a Bambu Lab printers MQTT service to determine when a layer...

housing for a Tuya Smart WiFi Relay 4CH boardwith WAGO clamp holderlight channels for the wifi and switch LEDs(second version for the lid with an universal name)dimensions:L:  130 mmW: 100 mmH: 28,5 mmdrillings:wall mount - 5,6 mmlid - 6 mmPCB - 3...

Be careful with the antenna lead when you assemble the sandwich together - mine likes to get trapped between the WiFi module and the case during assembly. Three M3x12 screws and nuts hold it together. I used a little tape to keep the battery away...

......If you're looking for the smallest case for Raspberry Pi with Waveshare 3.5" Touch LCD with out too much additional add-ons, this will be the ideal one to fit in both. Come with PCB support fixture. To keep LCD same height for matching LCD cover.

You can use it however you like - turn it into a Pi case for your Raspberry Pi and transform it into a control center for your 3D printer. This innovative device is built around the power of the Raspberry Pi and a 5-inch GPIO HDMI touch screen. To...

I just sliced a part away so you can connect to the GPIO contacts...it's the same as this one https://www.thingiverse.com/thing:2334119 The USB cable in the picture is connected to the printer, I needed the GPIO ports for https://www.lisiparoi.com/...

Second version with small adjustments to make it fit the Prusa Mk3 Z-support above the motherboard. ...Should be a perfect fit but not yet printed it myself.

I created this design specifically to feature the distinctive alternate octopus symbol, which consists of eight interconnected pi characters.

... for WiFi Mode with Topplokk Specifications. ... A Custom-Made Case Cover for the LMTS Rpi3 B+ Model in WiFi Configuration. LMTS - Our Project's Internal Code Designation. ... Project Source Files Available on GitHub at https://github.com/SenjaVGS.

This is a case for a Wifi & GPS device meant for Celestron telescope mounts at have available AUX ports.  It combines the features of a few commercially available dongles into one device. The full project discussion can be found at...

This is a case for a Wifi & GPS device meant for Celestron telescope mounts at have available AUX ports.  It combines the features of a few commercially available dongles into one device. The full project discussion can be found at...

it's identical to this one https://www.thingiverse.com/thing:2334119 The USB cable in the picture is plugged into the printer, I required the GPIO ports for https://www.lisiparoi.com/ I've updated the case to accommodate M3 or M2.5 bolts through,...

Heatshrink over the connection for added strength. Connect this wire to the 3V3 Power Pad/Pin on your Pi Zero W. Install the "Room Temperature" Plugin by Frederic Moutin, detailed here: https://github.com/l00ma/OctoPrint-roomTemp. Run the three wires...

This is a simple large case for a CellSol WiFi Pylon built using the recommended Heltec LoRa32 or V2 board. This has room for a larger battery box, such as 3 AA batteries, as well as any additional accessories such as instruments or data loggers you...

A simple case for the Joovuu X action camera. ...Just drop the camera in from behind.

To build this enclosure, you'll need: - 3D printed parts - Five 2.9 x 10mm tapping screws (four to secure the controller and one for the case cover) - Five 2.9 x 13 (or 16)mm tapping screws for the cover - Four M3 x 16mm screws and nuts (included in...

It consists of three parts: the front bezel, the mid section where the Raspberry Pi mounts, and the rear cover that encloses all components and features holes for the HDMI, power in, and audio ports. The entire assembly is held together with M4...

- `top_v2.stl` - original top - `top_v2_+2mm.stl` - 2mm thicker - `top_v2_+3mm.stl` - 3mm thicker - `top_v2_+2mm_noinserts.stl` - 2mm thicker with insert holes filled for M3 screws (no inserts necessary) - `top_v2_thicker.scad` - the OpenSCAD file...

v3 of the case for my RS485 to WiFi adaptor

Just a quick OpenSCAD hack of the original top_v2.stl to make it fit my WaveShare LCD (A) screen, which is somehow 1.x mm thicker than the one used in the original design.top_v2.stl - original toptop_v2_+2mm.stl - 2mm thickertop_v2_+3mm.stl - 3mm...

Components Used: 1 x Raspberry Pi 3B+ with OctoPrint Installed 1 x Waveshare 3.5" Touchscreen Display Thermometer: 1 x Arduino Pro Mini (5V Version) 1 x 8x2 LCD Display 2 x DHT22 Temperature and Humidity Sensors Touchscreen Menu Plugin for OctoPrint:...

Print all the parts or just print what you need, but be aware that for the gimbal assembly, you'll also need my camera housing design. Additionally, to make it fit your Raspberry Pi B+, you'll require 3mm bolts from the top. When the servos are...

I designed this enclosure to house the Duet WiFi control board on the D-Bot build created by spauda01, providing essential protection, efficient cooling, and effortless connectivity for all components. The project is now complete, with everything...

This case was designed for an USB camera module (38x38mm PCB) :https://www.amazon.fr/gp/product/B0BJ73WDSV/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1Camera PCB has to be screwed on inner pads using slef-tapping screws (2.5x8mm) ; please note...