octopi wifi camera case for b 3d models

This is the case for an independent OctoPi system suitable for my 5 inch touch LCD, Raspberry Pi 3 and stand for Pi Camera. Includes a stand where i mounted the Camera. Also i included guides for the camera cable, mounted in the arm pieces. I used...

English A case for the Raspberry Pi to get the most out of Octoprint, with short cable runs this case adapts perfectly to the Ender 3 v2, as if it was already designed that way at purchase. The 24V power supply line can be laid directly in the V...

... X-axis motor and the frame is only 8mm. To fix this, I modified the case to move it 16mm to the left, allowing enough room for my setup. ...Unfortunately, you won't be able to print this lying down on the back - you'll need to print with supports.

... enabling seamless use of the NavoLabs Raspberry Pi 3B+ POE Hat with this case. ...The base components remain unchanged for users who have already printed the original version, eliminating the need for reprinting.

SG ------------------------------------------------------------------------------------------------------------------------ I'm upgrading my Heltec ESP32 LoRa Wifi Case with a battery mod * Check out the case:...

I also rearranged the USB and LAN ports to fit the Raspberry PI 4B correctly, making room for the standard 30x30x7mm fan that comes bundled with the Pi accessory case. Additionally, I added USB-C and HDMI ports on the back, which can be extended...

This is a case I designed specifically for MOI3D on Raspberry Pi Model B+, tailored to use with OctoPrint, known as OctoPi, so hence the ventilation slots molded in my own unique OctoPi logo. It's worth mentioning that there isn't any opening...

To remotely observe your builds, attach a D-Link 930L or equivalent camera within your printer's enclosure using this bracket for optimal angle. The bracket fits snugly at the top left corner without obstructing rails or printing head. Remove the...

To create order, I have created a custom case for my Octoprint Rpi3. The case fits perfectly under the unprotected control panel of my Ender 5 Pro and should also fit the Ender 5. All connections of the Rpi are accessible. The mounting is done...

This is a Remix of https://www.thingiverse.com/thing:4328596 and https://www.thingiverse.com/thing:434600. Screws needed: 7x M3-nut 5x M3x16 2x M3x8 Only the sphere rod was printed with brim. ... Fan guard: ...

This is a Remix of https://www.thingiverse.com/thing:4328596 and https://www.thingiverse.com/thing:434600. Screws needed: 7x M3-nut 5x M3x16 2x M3x8 Only the sphere rod was printed with brim. ... Fan guard: https://www.thingiverse.com/thing:2505568

... screws can also be added. There's internal structure in the bottom, so only a thin layer of plastic needs to be removed to expose the screw holes. For a similar case for the model B+ and 2 model B, check out http://www.thingiverse.com/thing:978990.

(I didn't and it printed just fine.) Installation: * Removing the two screws in the front of the rail * Slide the case into place * Put the screws back into their place For cable management I used these clips https://www.thingiverse.com/thing:3107506...

(I didn't and it printed just fine.) Installation: * Removing the two screws in the front of the rail * Slide the case into place * Put the screws back into their place For cable management I used these clips https://www.thingiverse.com/thing:3107506...

Faults / Improvements for next version: 1) The bottom half of the case has small separators for between the USB / Ethernet ports. --> Their dimensions are wrong, so after printing - I snipped them off. 2) The Top half has un-even screw forces -...

I remove the switch hole and the grill and add a new grill for a 30mm fan (https://www.thingiverse.com/thing:2802474), what is connected to the RPI GPIO. ...Also I modify the LM2596 holders because the originals not match with mines and added a hole in...

**Fits this case**: https://www.thingiverse.com/thing:5470150 **With this case for the Wifi Dev Board**: https://www.printables.com/model/179910-case-for-flipper-zero-wi-fi-module-v1

Case for a wifi thermostat based on heltec wifi kit 32 board

The ideal case for a Raspberry PI B+ is running in tandem with a BCN3D+ printer. ...Using it with your printer will enable seamless execution of Octoprint software while rendering the Raspberry PI B+ completely invisible.

Octopus Housing Solution for Waveshare 4 Inch HDMI Display and Raspberry Pi System.

... Ender 3 Pro - Raspberry Pi 2/3/4 + LCD Enclosure by eoyilmaz. ... A modified version for the Ender 3 Max using Tinkercad. Fits great, add a fan on top of the pi for extra cooling. Note: Drill an angled hole for installing the last screw. ...

I used the original design for months but wanted to set up a second printer so I remixed it and added bigger cutout to make all 4 USB ports available.

The Raspberry Pi Type B case is a customized enclosure that accommodates mounting holes for seamless integration with 3D printers. ...Its exterior proudly displays the model designation "K8200".

This project aimed to create a case for the Raspberry Pi 2 that would be optimized for injection moulding using a simple two-part moulding tool. Several requirements needed to be met: The board is connected to the case with thread-forming screws. I...

Key assembly features include: * Board connection to the case using thread-forming screws * Design for easy assembly and disassembly * Ability to withstand static load of 20kg without deformation exceeding 1mm * Mass less than 70g * Cases must be...

I designed this case for my Raspberry Pi 4 B which i use in my home automation system with Loxone.Everything snaps together, you will ned no aditional parts or tools.

The pins for the bearings differ slightly from the original ones and are not compatible with those in the Soeren Stobbe project. If you decide to print this one from my project, everything you need is included within it. Simply download the zip...

This is a case tailor-made for Raspberry Pi 4 model B. To bring this project to life, you'll need a precise 3007 5V fan, four M3x12 countersunk head screws, and four 2.2mm x 16mm countersunk head self-tapping screws. ...The GPIO version boasts an...

Simple travel case for Oral-B type electric toothbrushes. Update: The wait is over, no more fiddling with parts, just print and go. ... Print Settings: Printer Brand: RepRap Printer: Prusa i3 Rafts: Absolutely not needed Supports: None at all ...