octoprint relay 3d models

Following a similar approach to the guide found at https://www.instructables.com/id/PSU-Control-With-Octoprint/, this project involves integrating a single relay module into a protective housing. To complete the design, I attached the lid directly...

A custom enclosure for Octoprint's relay mod is cleverly showcased by Miros on Instructables, where he thoroughly explains every step of the process. I took his ingenious design as a starting point and transformed it into a more compact version with...

Modules like these https://www.ebay.com/itm/5V-One-1-Channel-Relay-Module-ForPIC-AVR-DSP-ARM-Arduino/170937714367 https://www.ebay.com/itm/10pcs-Female-MICRO-USB-to-DIP-5-Pin-Pinboard-2-54mm-micro-USB-type/201540305451 Also you need 8 M3x6 screws...

Allows you to mount a RaspberryPi, 2 relays, and 2 buck converters to use with Octoprint

This design adds a case to your Ender 3 (Pro) that fits a Raspberry Pi 3 Model A+, a 10A relay (for switching LEDs on/off), a 30A relay (for switching printer on/off), a buck converter (for powering the Raspberry Pi from the Ender 3's PSU) and a...

- 9x M3 8mm screws (relays, buck converter, lid), 2x M3 12mm screws (fan), 11x M3 nuts, 2x M2.5 20mm screws, 2x M2.5 nuts (for RPi, alternatively M2 screws + washers are more common) - Cables and connectors - Power switch **Adding power on/off...

Control Your 3D Printer With Ease Using a Relay Case

I searched and searched for a convenient case design for my Octoprint Server with the following requirements: 1) Integrated 5V Relay Board (preferably 4 or 8 channel) 2) Integrated Power Supply 3) Raspberrypi3 Integrated w/ full port access 4) Four...

Introduction I have a Wanhao Duplicator i3, a raspberry pi 2 running octoprint (the octopi image), an LED light above the printer, and a 4 relay board from sainsmart. There are places with instructions, tips, etc. But I wanted to share how I did it...

This relay module can be controlled by Octoprint, allowing me to turn devices connected to it on or off remotely. To use this system, I just need to install the "PSUSupply" plugin and connect the relays to my RaspberryPi. ...With this setup, I can...

I followed this tutorial here: Turn Your 3D Printer On/off Using Octoprint NOTE: The tutorial specifies using a 5v GPIO pin for power, but for this relay I use the 3.3v GPIO pin as I found 5v is too much and the relay won’t work as expected. The...

**PSU Relay Module Housing for Pi Octoprint** I have a Taz 6 with enclosure + LED lighting connected to a Raspberry Pi running Octopi/Octoprint. The relay controls power for both the Taz 6 and enclosure lighting. For my Ultimaker 2+ with its built-in...

I needed a case to store my octoprint box consisting of an RPI3b+ and a KEYESTUDIO 4-channel relay PI-hat board. I started from this box that I slightly modified. I enlarged the hole for the SD card which was a little tight, I added holes to pass...

I needed a case to store my octoprint box consisting of an RPI3b+ and a KEYESTUDIO 4-channel relay PI-hat board. I started from this box that I slightly modified. I enlarged the hole for the SD card which was a little tight, I added holes to pass the...

The purpouse of this project is controlling printer power and an external light with OCTOPRINT, as well as all the tools Octopi includes. Raspberry is holded in its own case. ... It is a remix from a 2 realy box:...

You need: -1x Raspberry Pi B 3+ -2 channel 5V relay Arduino Raspberry Pi -1x Micro SD for Octoprint OS -1x Micro B USB Power Cable -1x MeanWell, RS-15-5 230V/5V power supply -4x jumper cable (short) -1x power cable -1x IEC device socket -1x 230V...

relays casing for a single 5v relays used with raspberry pi octoprint. can be mounted on a v-slot or where ever u want. ... no support needed i used a skirt since im using PEI sheet.

This is a switch box for Octoprint. ...In addition to the power contactor, there is also a 5 volt relay which can be switched via Octroprint and the Raspberry Pi. ... To print, this box is made of fire-retardant material.

Compact enclosure designed specifically for housing a Crydom D2410 solid state relay, successfully utilized to regulate printer power through integration with OctoPrint.

This is a combined enclosure design for an OctoPrint controller featuring the mounting of a Raspberry Pi 3B and a single 26mm x 50mm (20.5mm x 44.5mm holes) 120/240v 10A relay. The relay can be found here:...

PSU Relay Module Housing for Pi Octoprint I'm running a Tax 6 with enclosure + LED lighting connected to a Raspberry Pi that's got Octopi/Octoprint up and running. The relay module controls power for both the Taz 6 and enclosure lighting, making it...

I was scanning through Thingiverse trying to find a usable box to house my single channel relay but couldn't quite find what I was looking for. So I ended up making this simple little box. It keeps the printers power cable in place (not 100% but...

Octoprint Raspberry Pi Zero W with 30A relay module case for mounting on Ender 3 PSU (or wherever you want) to control prints and printer shutdown after prints or in case of emergencies.

I'm using this plugin in Octoprint to toggle the relay, which is connected to one of the Pi output pins: https://plugins.octoprint.org/plugins/psucontrol/. The Octopod mobile app also supports this plugin, so you'll be able to turn on/off via your...

octoprint raspi case with fan and dual relays for alfawise u30

Use super glue to attach the top piece to the Voltage converter Use 10mm VHB tape to mount: https://www.amazon.com/gp/product/B01BT0A6MG 24V/12V To 5V 5A Converter:...

Install the OctoPrint-Enclosure plugin for temperature evaluation and relay control 3. Add the following entries to the config.txt file on the Raspberry Pi: * `dtoverlay=gpio-shutdown,gpio_pin=3, active_low=1,gpio_pull=up` (Raspberry PI ON/OFF...

This thing is my go at building an active inrush eliminator to protect an Octoprint relay or any other relay you might be using to switch your 3D printer on and off. The case is a remix from another designer (linked to in this thing), but I have...

This is a simple enclosure designed specifically for use with a Raspberry Pi 2 B and a Relay Board, eliminating messy cables from around your 3D printer entirely. I utilize the relay board to switch my printer on or off remotely, which proves to be...

This one can also contain a 2-channel relay board to remotely cut off power to the printer, an Orange Pi Zero Plus to run OctoPrint, a 5V AC/DC to power the Orange Pi, and an 8x8cm fan to cool down the PSU, the Orange Pi and the AC/DC board. My...