oculus quest 2 3d modeling

5 walls, 0.1mm, x2 infill lines, triangles, 20% infill Cut Oculus Strap as close to the old clip as possible. Melt the cut end until there is one solid line of plastic on the end on the strap, for strength reasons. Print the new clips and use the...

The internal grooved one should accommodate a official Oculus Link cable. The top edge cable holder is a little larger in case you want to hold a headphone cable also. You may need to file down the opening a bit, if it is too small for your...

Print replacement straps for your Oculus elite (with or without battery) strap. There are three versions included:One piece original size (needs bigger print bed)One piece Prusa MK3 bed size (should fit most heads but may be tight if glasses...

This model requires a 1.5m hook-and-loop fastener. ... You should cut the hook-and-loop fastener to 5pices. 3 for the battery - mount, 2 for the mount - strap. ... The battery must be mounted upwards.

Works with the same 5x2mm magnets: https://www.amazon.ca/gp/product/B08H1N2HRJ Zenni Glasses to use: https://ca.zennioptical.com/p/metal-alloy-full-rim-frame-with-spring-hinges/5500?skuId=550021 The other remix increased the height of the parts that...

.2  2 layers concentric infill

UDATE 2: Re-Meshed the wings “conector” in blender, the V2 was made measuring the physical model, while this V3 is made by using the virtual model, allowing for a perfect fit with the base, they both work equally well, but it might be easier to align...

Slight remix to hang both controllers with only 2 screws.

There are 2 versions of this, one with AND one without secure tabs. Designed in Fusion and printed with Windows Print 3d using ABS. The rims for both are beveled. 1. Without Tabs - Just press the O into the rim. The rim is beveled and is...

After I finished sanding and spray painting this, I connected the triggers and buttons, and used a normal printer to make a BMW logo sticker to put instead of the Oculus logo. You will also have to use a knife to widen the whole at the bottom a...

3D-printable models for article "An open-source Olfactory Display to add the sense of smell to the Metaverse" in Journal of Computing and Information Science in Engineering. If you use this in your academic work, please cite as: > Lukasiewicz,...

remix grip from https://www.thingiverse.com/thing:4651978 608 2RS bearing * 2 20mm magnet rubber band M3 bolt nuts

Its a remix only bc I added 2 screw holes to the headset part, other than that credit goes to the OP. Thanks Headset didnt need support but the controllers did. I used tree, everywhere. ...

Modified Przemoc's design to wide fit I am not a professional modeler, so this modeling is a bit sharp I use this and the fov is about 10 degrees wider

... is a Minimal Print. ...intended to save filament Designed for both Headset and Controllers Required materials: 8 screws Notes: -You will need to print of 4 of these, 2 for the headset 1 for each controller -Print on its side to ensure maximum strength

... the layard. To install the layard: first put the lanyard in the hole, then loop over the clip and secure it in the 2 little hooks on each side. See photo. That how I install it but may be you will an other way haha. ... Print it flat, it's easier

This 3-file OpenSCAD project is a remix of the excellent "Oculus Quest Magnetic Prescription Lens Adapter" project by jegstad: https://www.thingiverse.com/thing:3659124/ Two of the three included files are unmodified from the version V2 of that...

This is a remix of another users model that wasn't wide enough. ...I went ahead and rescaled the model and added a spot to insert the grips of the controllers., the grips do fit rather snug and the wrist cords need to be over the top when inserting.

I used the snap-fit file, and I see a lot of decals out there, but nothing with designs for a 3D printed cover. I only found one other design, a Venom design, which looks incredible. ... You can find the others here: Original Blank: ...

... Then loop over the clip and secure it in the 2 little hooks on each side. See photos. ...That how I install it but may be you will find an other way haha.Print it flat, it's easierPrint SettingsRafts:NoSupports: NoInfill: 100Filament: PLA Grey

... ... UPDATE: As Promised, This is a link to the new Braced Headset Holder for heavier Headsets: https://www.thingiverse.com/thing:5727804 Sorry, but the file may have a few artifacts... I'm using Microsoft 3D Builder, So "It is what it is".

Composite version: Parts: 3d printed components long thin-walled 3/4" tube many short m2 screws 4-6 m3 screws + nuts 4 m4 screws + nuts 100% printable version: Assembly: Insert tube pieces into each other and push in the flexnails, adhesive/acetone...

I used the snap-fit file, and I see a lot of decals out there, but nothing with designs for a 3D printed cover. I only found one other design, a Venom design, which looks incredible. ... You can find the others here: Original Blank:...

... the top of the VR. Then glued the piece in place. lastly, a 3d pen was used to make a perfect seal, as well as a bit of low poly foam. You will likely have to trim the part a bit, it was made without knowing the exact headset curve... ...

This is basically just the model by tigerflip, but with a hole cut into the bottom. I measured the straps on my controller to ensure they could pass through (including the plastic thingy) but the fit is snug. You should pinch the strap and push it...

There is a recess within butt to conceal the knot. There is a hole in the butt that will fit a quick release sling swivel. Support free printable parts Print left or right handed controller clamps Print 3 clamp nuts Print one of each of the remaining...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi, but the adapter is movable, so I decided to make it 2mm longer and added a small clip at the end, so it does not get off...

Protective/decorative covers for your Oculus Quest 2 controllers! The holes allow proper tracking of the IR LEDs. Designed to be printed in TPU and slipped directly onto the controller. Three versions: (1) Original - Minimal with small holes. I...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi (https://www.thingiverse.com/thing:4624192), but the adapter is movable, so I decided to make it 2mm longer and added a...

For my BS CUBE, I split the main part to a length of less than 10 cm. ... The pins at the joint may need to be sized depending on the 3D printer you are using. ... I am deeply grateful to the original author.