oculus quest 2 controller 3d models

works with https://www.thingiverse.com/thing:3666505

Printed without supports 30% infill is probably overkill printed at 100% scale it is fairly loose on the mount (cable tie added some resistance) can be used also just to add some weight to the back of the headset i wasn't sure how much...

The Quest2 is front-heavy and slips down as you wear it, so I made a battery mount that doubles as a counterweight that attaches to the back of the headband. The battery mount should be installed by sliding it vertically after covering the Quest2....

<p>I printed it standing up with supports for the bridge</p>

<p>You need some 15mm wide double-sided velcro strips to hold the power bank and the mount.</p> <p>I'm using xiaomi 5000mAh (perfectly balanced) and 10000mAh (too heavy) power banks.</p> <p>Happy Gaming！</p> <h3> Print Settings</h3>...

Clip for double cable. ... Thanks rwmahr.

I was drawn to the short "stem" in the original design and the sturdiness of the design I remixed. By combining the two, I've created a new design that has yet to break. If you have access to TPU, I would recommend printing this design with it,...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

I wanted to use the head strap of Quest3 with Quest2, so I made it.Please be sure to read the notes below and use at your own risk.When attaching and detaching parts, there is a possibility of damaging the VR device itself.Depending on the strength...

The Quest2 is front-heavy and slips down as you wear it, so I made a battery mount that doubles as a counterweight that attaches to the back of the headband. The battery mount should be installed by sliding it vertically after installing Quest2.

Just removed 1.5 mm from the centre of the STL I printed in PLA but will print another in PETG for the durability and flex.

Designed this Cable clip to use with any cable up to 7mm thick. ...any cable smaller will fit but be a bit loose Printing: orientation: Make sure the print is on it's side this way it prints best and cleanest infill: best result use 100% but...

Headband for DAS Mod, includes a a buckle you have to glue on top so you can slide the end of your DAS nicely under it. Print with support everywhere. ... Remixed from: https://www.thingiverse.com/thing:3664951

Modified Przemoc's design to wide fit I am not a professional modeler, so this modeling is a bit sharp I use this and the fov is about 10 degrees wider

Comfortable back part PETG

This is a simple way to manage your headset cable so it doesn't hang down and get caught on anything while playing with your VR headset. I am working on an alternative design so that you don't have to remove the velcro straps everytime you wrap up...

Very light fan cooling system for Vr headset. It makes those beat saber sessions a lot more enjoyable. Also the foam does not get all damp after a long session. It's the perfect addition to the headset! Uses a small 5v fan (30x30mm) and a 1s...

Remixed to print flat. Mold around a round object after placing in hot water. ...Remixed from https://www.thingiverse.com/thing:4628591

Come si vede dai file, si tratta di un remix degli oggetti sopracitati ( https://www.thingiverse.com/thing:4629343 e https://www.thingiverse.com/thing:4629958), uniti e opportunamente migliorati per evitare una stampa di 4 ore per pezzo, ma con la...

My clip broke when I threw the disk too hard in Echo VR, I designed this so it can connect without a new strap. It is a bit hard to put on and it is snug at the beginning, after some time it will lossen up and be even better than the original. ... ...

A battery holder for the EAFU Portable Charger, Compact 10000mAh as found on amazon for only $10-15 usually. Its cool to see a number percentage left on your battery. It's a little tight the first time you slide it in but it gets looser later. It...

Remixed from https://www.thingiverse.com/thing:4629958 This clips on to the loop on the back of the elastic headstrap.

This cover is a remix! I used the snap-fit file, and I see a lot of decals out there, but nothing with designs for a 3D printed cover. I only found one other design, a Venom design, which looks incredible. ... You can find the others here: Original...

This adapter is slide-in assembly. The main purpose of using the sliding-in installation design is to reduce possible damage to the main body of the VIVE DAS during installation. please refer to the animation for details.

First thanks https://youtu.be/_fK8KaJDeaM I was inspired to design this connector. I hope you like it. ...

See https://www.thingiverse.com/thing:4630669 for details. Modified to allow mounting to the CAMVATE Universal C-Clamp: https://www.amazon.com/gp/product/B018RLY6B2/ Particularly useful for temporary desk mounting, such as when doing VR dev...

This is a remix of two things. The zip adjustment from https://www.thingiverse.com/thing:4625623 and the ring attachment method from https://www.thingiverse.com/thing:4625898. For some reason Thingiverse won't let me select both as a remix. My...

The original design (while being super comfortable, thanks so much) broke several times with my flimsy PLA. First time i used Blender, took me a whole evening to select all vertices and pull them out a bit to make it thicker. I included the...

Fits like a glove. All cables 3 - 6mm thick work. Plenty strong and secure. ...Easy to remove your cable without removing the clip(s).