oculus quest 2 gap around nose 3d models

... orientation. This mark should align with a cutout on the top of the holder. Please note that when using diopter -3.5 (CR 39) lenses in the Quest, this setup sits very close together. ...Thicker lenses may actually touch and scratch each other.

This is a simple design for Quest/RiftS Touch controller cups based on [this design](https://www.thingiverse.com/thing:2057419/files). The controllers have a tiny bit of wiggle room, but most of your fingers hold onto the cups anyways, so they won't...

Universal head power bank holder for the standard OCULUS QUEST2 strap or for other VR glasses with a similar strap system. Do you need to play VR for longer? This inexpensive practical solution is now available. Threading the tape from the VR through...

This is a grip designed specifically for the rift S and quest controllers that mimic the Valve Index knuckles control, allowing you to release the controller without worrying about it falling. Inspired by the MAMUT grip for the original Rift, this...

Alternatively, you can use a USB Type-C connector and plug it directly into your Quest. Here's the Bill of Materials: - Two 30mm fans that operate at 5V (find ones with reliable bearings for minimal noise). Check out this product:...

... some light, I might make light blockers in the future. I recommend this, personally, I think the improved FOV is great for immersion, and having nothing around your eyes feels much nicer. ... I personally don't think the light leaking is that bad.

... so be cautious. The rebalancer is attached by a small plastic clip, which can break off if you whip the controller around aggressively. ...I feel safe using this design, but I do not recommend it for those who are concerned about its durability.

The tolerances are quite tight, so you may want to print the top part at 102 or 103% size and wrap a piece of tape around the male part for a snug yet easy-to-assemble fit that's still simple to disassemble. This is the right-hand gun; mirror it for...

... Bionik Mantis headphones to the VR headset. ...It just sits nicely without touching the ears too much, akin to the Valve Index's over ear headphones I applied a light amount of hot glue on the inside for friction so it doesnt slide around the strap

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Begin by scaling down the pin to around 95-97% of its original size. Since the part is relatively small, printing multiple iterations until you get a tight fit won't be a problem. ...Once you've obtained a snug connection, simply use super glue to...

Holder for UGREEN Powerbank 10000mAh Power Delivery 18W USB C Power bank Print with TPU ~ 98 Shore A Edit: added a minimal version for maximised comfort, its fixed with zip ties so not clip on like the bigger version. Edit 2 the powerbank supports...

It's actually more comfortable with this battery pack on my Quest 2 then off lol. The model is a bit messy because the original file I remixed was corrupted. It may have some weird artifacts here and there but it prints solid and works perfectly. See...

... on the front for the logo overhang. After the print was completed I hot glued some foam and velvet to the top to prevent scratches while using the stand Print time: 17hours on Snapmaker 2.0 on normal filament quality, 10% infill, ironing On

2- A modded version of the shelf (oh the places you'll go) 4- The 'shelf' piece with no words as a Fusion file 5- The 'stand' piece with no words as a Fusion file **Tomorrow All of the pieces are appropriately sized and be printed as they are. ... ...

Using this mask also reduces the gap between your cheeks and nose when wearing a mask, providing a sense of security. (It also helps prevent clouding on glasses.) The material used is STL. Thanks for trying this out! Enjoy! ... Update History:...

This is an old model. For newest adapters, please visit https://solidslime.net This adapter is designed to give a better feeling to the Eleven Table Tennis who prefer to use controllers (or controllers with very light weighted adapters). (If you...

Remixed from Tanvach's adaprter, it's able to use the Rift headstrap (you need to grind/cut off the metal piece that attatches itself to the headset.) with some minor modifications. This is the first project I've made and uploaded, so please bear...

This is a clip modification only for the original clip designed by fortinmike. The pin hole remains the same so all original pieces should work. ... The Clip is resized to fit 3rd party straps similar to the Orzero head strap (found on Amazon) Make...

Modification of the original model for use with https://www.thingiverse.com/thing:3653631

There are two design versions. One blank and one with the logo from the custom home environment community. Both versions are available in split and without split. The split version is easier to print but you have to glue the parts together. ...

this remix replaces the previous mounting method with holes to screw these mounts directly into the wall, which i have found to be more sturdy. please visit the source post for more information on how these parts work and to support the original...

Thanks for the Scan! This is my quick clean up, possible now to print without supports and adhesion is improved on first layer. Further edits like nubs where the buttons would be might be added to make it feel more realistic, possible further cleanup...

I wanted a bulky protector from https://www.thingiverse.com/thing:4745565 for thrill of the fight and other games, and also liked the knuckle straps from https://www.thingiverse.com/thing:4625623 so i kinda merged them together in 3d builder. Not...

<p>I came up with a battery holder for the Anker PowerCore10000, but getting the whole set up in my case required putting the battery in a bag and letting it ride the lenses.</p> <p>This would not do.</p> <p>So I spent 10 minutes in 3D Builder and...

I followed this reddit post to put my broken Elite battery on my Bobo VR M2 halo strap.  I wasn't happy with the taped together straps, so I designed and printed a replacement strap. I designed this with my printer tolerances in mind and it's a good...

Just a Battery Holder for my Headstrap I've printed it in TPU to give it a bit more flex

This is an adapter for 3rd party straps to make the strap more compact and comfortable. ...It raises the strap by a few cm and allows for it to compact down a lot better.

I was printing and assembling the magnetic gun stock from Teque5 and decided I wanted a fancy muzzle brake. Found CloudyJ84's design and merged the muzzle piece into the base of the dragon head. ...Didn't print perfectly but I think that's more my...

Simple Battery Strap that holds a power core battery. ... Slides on the strap at the top of your head.