oculus quest 2 ipd range 3d models

Printer / settings used: Voxelab Aquila S2 Print Temp - 205 Bed Temp - 60 Speed - 100% Initial Fan Speed - 20% Until Layer 10 Regular Fan speed - 100% Support - N/A Layer Height - 0.2mm Infill - 20% / Cubic Subdivision Plate Adhesion - N/A Slicer -...

This is for https://www.thingiverse.com/thing:4788056/comments#comment-5701349 for printers that can't print the larger design. ...Took off the wings and made it super basic.

For a long time I was looking for some nice lightsaber with which to play a good beat saber. so I decided to make it myself :) The lightsaber is fully printed consisting of two parts. ... unprintable part: the non-printable part is a threaded rod...

Simple cable holder

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

This is a remix from https://www.thingiverse.com/thing:398515 I used the snap fit file printed great on Ender 3 v2 and added the venom eyes on it. ... I used .3 resolution to cut printing time but at a .16 will look much better.

Helps with the sound quality and volume a bit (and possibly some isolation), For a demo hover cupped your hand over your ear and get a similar effect and help you verify if this print is for you. ... side effect is that it could also amplify the...

Have been looking for a charger brick and cable holding solution, and the packaging box just isn't cutting it? Here's your solution! Simply print, place, and secure! - Print: Follow printing settings below (Place flat bottom along build plate!) ...

Inspired by the designs of Elizer and Spatz0r https://www.thingiverse.com/thing:4631187 https://www.thingiverse.com/thing:4657761 I've moved the clasps forward so that they firmly attached to the rigid part of the strap. ... Easy print , easily...

A great cap to cover the fabric strap. Keep it clean for a while (Mine was grey after 1 week) I made it symetric for use on both side. ... Just print it, clip it and enjoy

A remix of https://www.thingiverse.com/thing:4724688 splitting it for smaller printers. I split the model with a half lap joint to make it stronger and allow a good surface area to glue it. ...The O in the design was removed to allow for a thicker...

Printed in PLA and secured with double sided gorilla tape. ...Can print the x's in a different color

Filament : PLA Layer height : 0.2mm Infill : 30%~40%

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/6YtVq26tr2F

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/6YtVq26tr2F

Most of parts printed with support from bed or without them. Basic setup: (Bot_Part + Top_Part + ScrewTall + simplestHolderWithHole) x2 you can put whatever weight inside "simplestHolderWithHole". Setup with casted weight: (Bot_Part + Top_Part...

i made this model to add weights to my VR workout sessions. apparently controllers normally weight 149 grams any when i added the container and screws inside it it weights 275 gram and is good enough for fast paced rhythm games. of course you can use...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/cSMtSc2kJ2c

Made this to make the cooling system less restrictive on the main cooling system, it does require cutting into the front face plate.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/6YtVq26tr2F

Works with almost any battery

My final version of an elite strap alternative: Advanced Strap I tried to imitate the elite strap as closely as possible. i think the plastic alone is very convenient, but i added an optional padding! Simply print it with some flexible material...

This is a remix of https://www.thingiverse.com/thing:4130801 and https://www.thingiverse.com/thing:4623302. ...The design is still a work in progress as the fitment isn't quite right but I'm not sure if that's because of my printer.

I use Sanlaki controller mounts, which is a bada$% gun to build I just wanted something smaller that's easier to hold. Open 3mf files as project in Cura and all my settings should be included. ... (Pipe) ...

<p>Made this to make the cooling system less restrictive on the main cooling system, it does require cutting into the front face plate.</p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>Creality ld-002h</p> <p class="detail-setting...

A remix of Crispy3DPrint's Design but with no room for the headset as I have found you can just sit it next to the dock. ... Crispy3D's Design: https://www.thingiverse.com/thing:4724688

Took a stab at flattening the original model, for printing with flexible filament. ...Remade the hooks with a small incline to print without support

This is a remix from https://www.thingiverse.com/thing:398515 I used the snap fit file printed great on Ender 3 v2 and added the venom eyes on it. ...I used .3 resolution to cut printing time but at a .16 will look much better.