oleo 10 puzzle 3d models
343008 3d models found related to oleo 10 puzzle.prusaprinters
Remake of Oleo 10 Puzzle by Yuu Asaka Print instructionsThe print you see in the pictures was made with 0.15mm layer height and 15% rectangular infill According to the puzzles official specs It should measure 13.6 cm x 11.6 cm x 0.6 cm I made a...
prusaprinters
This is a 3D printable remix of the Oleo 10 puzzle. ...(For ender 3/3 pro)</p>
prusaprinters
When the puzzle is at rest (not solved) there is a storage slot for the extra ring.Print instructionsOleo 10 - Art DecoThis is my version of the Oleo 10 Puzzle - recreated from scratch. I liked the puzzle, but i did not have any place to store the...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714444 Instructions Using the following options: font_catch_diacritical_sign = 2.3 baseheight_percent = .33 do_shift_font = automatic textstring = Hallpass7 RoundedBase = 0 basethickness_percent...
thingiverse
STL from: https://www.myminifactory.com/it/object/3d-print-10-digits-puzzle-72142
prusaprinters
STL from: https://www.myminifactory.com/it/object/3d-print-10-digits-puzzle-72142 Category: Toys & Games
myminifactory
This is a 10 piece puzzle cube that ends up becoming a 6 by 6 by 6 cube.
thingiverse
This is a variant of the "10 Penny Puzzle" which is rescaled for Euro Cents instead of US Dollar Cents. The original https://www.thingiverse.com/thing:2973413 by totallyaddicted just was shrinked by a factor of 0.853. If you can read German: Mehr...
thingiverse
10 US pennies can fit inside of this puzzle. ...Can be printed at fairly low quality as seen in the picture
cults3d
So - another 10 digit puzzle was born. But don't worry - included base is without text. Although - if you print it, be warned - if your printer even slightly over-sizes prints, you must work with sandpaper, as in my mind was puzzle that is tight...
thingiverse
So - another 10 digit puzzle was born. But don't worry - included base is without text. Although - if you print it, be warned - if your printer even slightly over-sizes prints, you must work with sandpaper, as in my mind was puzzle that is tight...
myminifactory
My Lockpick puzzles are the result of my goal of creating a print-in-place puzzle that comes off the print bed ready to solve! This is puzzle number 10 of 10. I tried to make it so the puzzles become increasingly difficult through the series,...
prusaprinters
A fun little puzzle using 10 x 1 Cent coins (EUR). Try and place the 10 coins inside the square. Changes over the original:adjusted tolerancesadjusted the border of the Tray to make it equally thick on all sidesremoved the embossed...
thingiverse
A fun little puzzle using 10 USD Pennies. Try and place 10 pennies in the square. It's not too hard. The solution is shown in the last photo. I've included a penny model if you do not have access to US money. Just print 10 of them. You can...
prusaprinters
Thanks! Print instructionsCategory: Puzzles Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 10% Notes: Any setting will probably do as this is a fairly simple print. ...If the tolerances...
myminifactory
I found this awesome puzzle on the internet and have created a printable version of the puzzle with Fusion360. Note: The last three pictures show the solution of the puzzle. So do not open these if you want to puzzle yourself. ... Have fun with the...
thingiverse
Although not very difficult, this puzzle is an intresting idea and it might have only one solution (I am not 100% sure). Estimated time to solve this puzzle: ~5 min. Ten pennies required. I will not post the solution here so if you think...
myminifactory
Although not very difficult, this puzzle is an intresting idea and it might have only one solution (I am not 100% sure). Estimated time to solve this puzzle: ~5 min. Ten pennies required. I will not post the solution here so if you think you've...
cults3d
Although not very difficult, this puzzle is an intresting idea and it might have only one solution (I am not 100% sure). Estimated time to solve this puzzle: ~5 min. Ten pennies required. I will not post the solution here so if you think you've...
cults3d
The Wave 5, Wave 7, Ice 9 and Oleo 10 each have their own size, while Bird 11, Jigsaw 16, Jigsaw 19 and Jigsaw 29 are the same size and can use the same STL files. I printed the frames in white PLA and the lids in transparent PETG so you can see...
thingiverse
The Wave 5, Wave 7, Ice 9 and Oleo 10 each have their own size, while Bird 11, Jigsaw 16, Jigsaw 19 and Jigsaw 29 are the same size and can use the same STL files. I printed the frames in white PLA and the lids in transparent PETG so you can see...
thingiverse
You can choose between the two types of centers, one have 3 points and the other have 4.I recommend to use a lube, spray or drops to ensure the smoothness of the puzzle, you can choose the stickers. ... You will need a M3*8 screw to secure the center...
myminifactory
This is the second cylinder puzzle I've made. It is about 100mm in diameter, and just under 40mm tall. (Not including container). It consists of 41 pieces of varying size and shape. And it all fits perfectly inside a container to solve in, and store...
thingiverse
Some fun with OpenScad again : a puzzle that i found on the web, rendered using 'boxels' and heavy use of arrays. ...(mooncactus hinted me about using more of these) be carefull, do not open the coloured image unless you want to spoil yourself (it shows...
thingiverse
Here the Euro version of 10 in a Square (https://www.thingiverse.com/thing:4790683). As it is valid for the original, you can use Prusa Slicer or other slicer to make a color change for the letters. Otherwise, just leave them and they will print in...
prusaprinters
Here the Euro version of 10 in a Square (https://www.thingiverse.com/thing:4790683).As it is valid for the original, you can use Prusa Slicer or other slicer to make a color change for the letters. Otherwise, just leave them and they will print in...