olympus 35 rc battery 3d models
145747 3d models found related to olympus 35 rc battery.thingiverse
Really simple thingy. ... An insert that fits snuggly in the battery cap for the 35 RC. It allows for the use of a 675 sized hearing aid battery instead of the original Mercury PX625 battery. ...
thingiverse
Replacement lens cap for Olympus 35 RC Rangefinder, because mine kept falling off. The 35 RC is a rangefinder, and as such can be focussed with the lens cap still attached. Sometimes I am extremely stupid and take photographs without first removing...
thingiverse
This is a lens cap for the Olympis Trip 35 camera. ...It also fits the Olympus Pen range of the same era, eg the Pen-EE, Pen-EES etc. ...The inside diameter is 45mm.
thingiverse
This is a case for Olympus BLS50 batteries. It has one hole from each side with the discription of full and empty. ... Each battery have one little triangle ,that i paint it with a marker, and you have to place it in the right side of the case to...
thingiverse
This is a battery adapter for an Olympus e500 DSLR camera. Used to replace the battery and power the camera with a 7.2V DC adapter. Use at your own risk. This may permanently damage your camera. I am not responsible for any damages Post-Printing You...
thingiverse
I needed a clean way to store and organize my Olympus OMD EM-5 batteries, this does a great job at that. ...
thingiverse
Click on top cover for an Olympus BLN-1 type battery. Created in Solidworks. ... Be gentle guys, it's my first design...
thingiverse
I purchased this lens [Olympus 35-100mm F2 ED for Four Thirds (and it is no longer in production, was very expensive when it was originally sold,) and it was missing the tripod collar, so I made one to replace it. There are four parts that need to be...
prusaprinters
I purchased this lens [Olympus 35-100mm F2 ED for Four Thirds (and it is no longer in production, was very expensive when it was originally sold,) and it was missing the tripod collar, so I made one to replace it. There are four parts that need to be...
thingiverse
... to be printed with color change. ...If your battery is empty, simply flip the lid to indicate charge status. Depending on printer settings and callibration, the lid may need reduce thickness a little. ... Made for Olympus BLS-5, BLS-50, PS-BLS1
thingiverse
This is another remix of gernesha's battery cap, this time for the Olympus BLS-5 battery. It is my understanding that the BLS-1, BLS-5, and BLS-50 batteries are the same size and therefore should fit this battery holder as well. These are used in a...
prusaprinters
Olympus BLH-1 battery case. Tight fit around the battery.Has an indicator hole so you can indicate whether it's charged.Slightly smaller than the original clear plastic caseMuch easier to useNo thin plastic flexy clamp arms. ...Uses a couple of...
thingiverse
This is a battery holder for Olympus BLH-1 batterys. I found the idea here for Canon LP-E6 batteries and took my own aproach to this. UPDATE: 30.01 Did my first Print (which failed for other reasons) and made some adjustment according to my...
thingiverse
This battery magazine holds three OMD EM10 Mark VI batteries
prusaprinters
This is a pretty basic case for up to 3 LI-92b batteries. This lid snaps into place with the indents. The case is square, so the lid fits in any orientation. I printed with PLA with 0.2mm layers and 15% infill. Probably could do less infill as there...
thingiverse
Motion RC Freewing F-35 V3 EDF Jet Battery tray + Frsky X8R or L9R Rec holder. ...Uses two 3x6mm screws.
cults3d
Motion RC Freewing F-35 V3 EDF Jet Battery tray + Frsky X8R or L9R Rec holder. ...Uses two 3x6mm screws.
youmagine
Clips on the Olympus BLS-5 Battery used by the popular Pen-Cameras and covers the contacts to prevent shorts. ...It features beveled edges and corners to stop it from poking holes into your gear.
thingiverse
Dummy battery for Olympus camera BLS-5. PCB need to be developed by yourself. ...Use 10kOhm resisotr between minus and T field.
thingiverse
Remix of the BLS-5 Battery Holder of vrmmm to keep 3 batteries together Original Olympus battery fits very tight, Hahnel battery is much looser (but can be fixed by sticking some tape on the battery to make it thicker) The clips broke of on my print,...
thingiverse
This is a battery cover for Olympus BLS-50. It is designed with Design Spark Mechanical 4.0. I printed with Elegoo MARS UV 3D printer with default parameter with NOVA3D UV 405nm transparent resin. ...
thingiverse
Battery box for 5 BLN-1 Olympus camera batteries. original lid was a little tight ( had to pry to open) so uploaded a new lid should print more loose. batteries fit both ways so make sure curved sides are on the right side or it will be tight...