olympus 45mm f1 8 lens hood 3d models
369116 3d models found related to olympus 45mm f1 8 lens hood.thingiverse
Simply print and snap on. Some xacto knife and sanding jobs may be required. It's reversible! Update Jan 24, 2018: Modified modeling for the more tight fitting. Instructions Recommended setting:...
thingiverse
A simple straight hood design for the Olympus 45/1.8 lens. The narrower field of view of this lens can use a straight tube for a hood which make it much more compact when reverse mounting it on the lens for storage. I made this one about as long as...
thingiverse
... Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=414556 Instructions Using the following options: cap_diameter = 370 cap_name = 45mm f1.8 cap_label_position = inside cap_tolerance = 125 cap_pitch = 75 cap_thick = 1181
thingiverse
My first version was more compact but did not have room for your fingers to remove the lens cap and it could not be reversed. This version can be reversed and even with my thick fingers I can remove the lens cap. Don't mind the ridges you see, they...
prusaprinters
needed a balancing ring for a 25mm Olympus lens to mount on a x5s inspire 2 camera form dji. ...so designed a lens hood and bayonet fitting for the 25mm lens, which weighs around the same as a balancing ring resulting in a balanced gimbal
cults3d
A stadium / discorectangle shaped lens hood with reversibility for Olympus M.Zuiko 45mm F/1.8 Tested and no vignetting problem No problem with lens cap and filter too.
thingiverse
... Note that there is a plastic ring that covers the bayonet mount on this lens. Remove the plastic ring, then add mount the lens hood. This is a simple hood to keep stray light coming from the side out and to protect the lens' front element.
thingiverse
This lens hood is a clone of the Olympus LH-40B, which is designed for the 45mm f/1.8 lens. It is reversible, and also clicks in place similar to the Olympus-hood. It is fairly tight, so may need to be tweaked depending on your printer's bias. ...
thingiverse
This is a remix of Manticorp's hood for the Canon 50mm f/1.8 STM lens. I used the original as the basis and redrew it in FreeCAD. *** Note that it is design for the new STM version. *** Having acquiring the lens, I don't want to pay the ridiculous...
thingiverse
Olympus Zuiko 45mm lens case. ...There is some space inside for sponge filling.
thingiverse
Didn't feel like paying for a lenshood and wasn't sure if there was a different between the EF and RF 50mm F1.8 so I designed this one myself. Got a bit lazy with precision so I ended up printing this at 102% on the X and Y axis and 100% for the Z...
cults3d
Didn't feel like paying for a lenshood and wasn't sure if there was a different between the EF and RF 50mm F1.8 so I designed this one myself. Got a bit lazy with precision so I ended up printing this at 102% on the X and Y axis and 100% for the Z...
thingiverse
Fits perfekt for Sigma Lens. ...With little nipple show were to put...
thingiverse
Basic Lens hood for the Olympus 12-50mm f/3.5-6.3. ...printed with no supports.
thingiverse
A lens hood for Canon EF 50mm f1.8 STM lenses. ... Can be used both as as hood and as a protective case.
thingiverse
This is a lens hood for Canon 50mm F1.8 EF STM. ... It can be screwed to the lens the other way around.
thingiverse
This hood lens fits on all Olympus M43 lenses 58mm diameter, the m.zuiko 40-150 it's a popular lens in ordinary kits. ... Can mount the hood as original, fit on the external lenses bayonet and turn some degrees for lock, Can mount inverse for less...
prusaprinters
A lens hood for Canon EF 50mm f1.8 STM lenses.Can be used both as as hood and as a protective case.Print SettingsResolution:0.1mmInfill: 100%
thingiverse
EN: Because my Sony 50mm F1.8 fullframe E-Mount lens has no lens hood. The original are quiet expensive, therefore i created a 3D model. The design uses the lens lock mecanism (bayonet + click / snap in). It could be attatched in front and...
thingiverse
This is a design for the Canon 50mm F1.8 that has a hood diameter of 49mm. This has been tested with PLA at 30% infill, no supports. Light filing may be required but fits very nicely. Have't tested on ABS. SCALE BY 10x! ...(scale to 1000% initially in...
thingiverse
I tried to print 50mm canon lens hood by oldhui (https://www.thingiverse.com/thing:3298377) but after that, I had a lot of problems with removing the supports. So I redesigned his model to avoid using supports. Now the hood is working nicely just...
cults3d
I have absolutely no interest in paying $60 for an official Canon piece of screw-in lens hood weight less than 10 grams so I designed my own in two versions. One with a completely smooth finish and the other with ridges. ... I found the ridged one to...
prusaprinters
I tried to print 50mm canon lens hood by oldhui (https://www.thingiverse.com/thing:3298377) but after that, I had a lot of problems with removing the supports. So I redesigned his model to avoid using supports. Now the hood is working nicely just...
thingiverse
Amazon was selling this for $30 so I decided to just print it instead SEL85F18 Lens Hood for Sony E Mount 85mm F1.8 Lens
thingiverse
I am publishing here my lens hood model for the olympus 75-300 II lens. I made the inner surface ribbed to reduce glare. I recommend painting the inner surface with black paint, for example with a permanent marker. Use it with pleasure! I...
thingiverse
This is a remix of two lens hoods for the Olympus series, i just remixed them to fit the M.ZUIKO DIGITAL 40-150mm 1:4-5,6 o58 lens. One classic, one fancier. ... You can print both without supports, both prints need around 1h40min at a Layer Height...
thingiverse
This was derived from Glyns Parameterized flanged lens hood, but I found the Olympus 60mm macro has 2 lugs and his design had 3. So I edited the SCAD file - new adventure for me. ... The striped print is just because I like changing filament during...