olympus omd grip 3d models
33399 3d models found related to olympus omd grip.thingiverse
A grip for the Olympus OMD E-M10 mkII camera. It could also fit the other E-M10 models since they have very similar bodies. Not only does it (significantly) improve grip while using, it also relocates the strap attachement points to the bottom of...
thingiverse
This battery magazine holds three OMD EM10 Mark VI batteries
thingiverse
When my Olympus OMD camera battery compartment lock failed, I could not purchase a replacement anywhere. So I just designed one. Worked well on my OMD E-M5 Mark II, but it looks like other cameras have exactly the same. Print in the finest...
thingiverse
I own a lovely camera, the Olympus OMD EM10, the original, mark 1. I have other cameras, but this is my workhorse, it's light it goes everywhere and has a rather annoying floor. The eyecup always works loose. I noticed it when I bought it but became...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Loop_x_position = 13 Rotation = 50 Loop_y_position = -7 height = [5,6,4,5,4,3,5,4,6] Font_name = Lobster Loop_character = o spacing =...
thingiverse
Grip for Olympus OM-1, based on the OM-4 grip by @digduck (https://www.thingiverse.com/thing:2952837). ...I have not printed this yet, so I don't know how well it fits.
thingiverse
I have olympus E-pm1. ...it is a very thin camera to hold. So i decided to add a grip made of 300micron PLA or ABS. it takes 50 minutes to complete. use a heated bed. ...tep 204 celcius for hotend.
thingiverse
Replacement Hot Shoe cover. ...I based the design on the Olympus OMD EM3 Mark II model. ... I included the Fusion 360 file so you can customize it if wiished
thingiverse
# Olympus OM2/n half grip Next up in my camera grip collection is the Olympus OM2n as I recently got my hand on a couple. As usual, having large hands, these tiny SLRs tend to be on the slippery side, so I designed a half grip that secures on the...
thingiverse
This is for the MK1 version of the Olympus E-M10 and I'm pretty sure it won't fit on any of the later versions. I printed the one in the pics at .2mm layer height which I think looks pretty good. .1mm is certainly a bit smoother, but I didn't want...
thingiverse
This is a remix of an Olympus OM2 grip adding an arca plate mount for tripods.
thingiverse
Custom grip for OM-D camera (Olympus E-M5) Instructions Added a lip so grip doesn't turn. ... If you want to have access to battery without removing grip, you can cut this part using a sharp knife.
thingiverse
A replacement grip for the Olympus E-M1 II. I printed it out of Nylon + CF. There's a tiny lip at the base of the grip, around 0.6mm deep. This small lip may need to be filed down slightly on the lens side until it fits, while remaining intact on...
thingiverse
I designed this version of the OM system Camera Grip 1 based on the original Camera Grip 1, which currently is extremely rare and thus quite expensive. I am fortunate enough to have two of them, and thought in creating this would allow others to...
thingiverse
Roger is an accomplished photographer who I saw using a palm/hand grip on his Olympus M-Zuiko 150-400mm lens in order to make hand-held shooting more comfortable. The grip which Roger uses was designed and built by a friend of his called Edward...
thingiverse
For the Olympus Pen D series cameras Olympus only made a matched flash unit which takes flashbulbs. To use an electronic xenon flash one either had to use a generic bracket, epoxy a cold shoe on to the plate, or use the small Pen flash bracket made...
thingiverse
My handle design for olympus em10 mark iii. Battery and memory card can be removed without removing the handle. Supports required for bolt hole. The handle itself does not require supports. For assembly you also need 1/4 inch screw for attaching...
thingiverse
Olympus has posted the stl of the thing that inspired this design herehttp://opc.olympus-imaging.com/playair/accessory/ !!!!!!!!!!!!!!!!!!!!!!! This allows you to hold your Olympus Air more easily and have a direct view hole to slightly aim where you...
thingiverse
As per request, an E-M5 MKII Grip with integrated Arca Swiss plate. ... As I dont have an E-M5 MKII, I dont know about the fitment.
thingiverse
The original grip design is by Scott Garriott, you can find his model at https://grabcad.com/library/e-m5-mkii-diy-camera-grip-1 I know EM5mk2 is a 2015 camera, I use my design for a long time until my friend ask me to share it. I tweak some...
thingiverse
Drog33 did a great job designing a grip for the OM-D E-M10, unfortunately it wasnt the greatest fit for my hands, I made it a bit larger and grippier, and added an internal space for a 1/4-20 nut so you can mount whatever you want to it. ...Just insert...
thingiverse
I shoot a lot of down low images. ...This grip allows me to easily shoot the camera in a very ergonomic way! ... I've included my source 3mf files I used to cut the model!
thingiverse
Source link here: https://make.dmm.com/shop/94512 This is a grip designed by the person in the link above for the Olympus Air A01 Luckily they've chosen to share the design! I'm uploading it here so I can help preserve the Air A01 files made by...
thingiverse
Remix of a brilliant grip for one of my EM-10s. ...I wanted a grip with integrated Arca-Swiss plate, si I just remixed one.
thingiverse
I already use my Olympus AIR A01 a lot with my Joby griptight gorillapod "base". so I thought, I can go and modify the S-Grip2 to make use of this mounting sceme, for quick and easy tool free transitions between tripod, car mount, and the S-Grip2...
grabcad
Grip attaches to the tripod mount. For Olymus OM-1 and OM-2 film cameras. ...With how I printed it, I printed a bushing to be glued into the 1/2" hole in the base to form the proper stack height for a 1/4" diameter machine screw that is approximately...
thingiverse
The OMD Filter Clip is a holder for 27mm unframed filter for astrophotgraphy and Infrared photograpy. ...Usable for modified cameras as well as for unmodofied.