one 2 up 3d models
1506869 3d models found related to one 2 up.thingiverse
... UPDATE.... It seems the edges will wear over time and increase resistance on the filament, it seemed to carve a shallow trench and bind a bit. Anyone else observe this also? Instructions Intended to work with my z pulley mod for the one up two up.
grabcad
Copy of sawamura one'up shad silicone lure. More than 70 models - please contact. Модель силиконовой приманки в .stl. ...Более 70 моделей - обращайтесь.
thingiverse
Small coaster with the 1-up mushroom from Mario bross. Printed in PLA standard settings. no need for support. ...infill less than 10%
thingiverse
"Prime-Line 2-Pack 1-5/32" Nylon Sliding Screen Door Roller Assemblies with 1" Nylon Wheels" This is the same one that Phantomopertor used in his version of the pulley mod. It can be found at most home improvement stores, I got mine specifically at...
cults3d
Here I have designed for you the Power Up or One Up mushroom. Of course, again for Led lighting. Eyes and face can be printed individually. Model fits on a 220x220 print bed. You have to drill the hole for the led output by yourself. So the model...
thingiverse
... a bowden extruder ! UPDATE V2: I needed mor space to let some screws slide under the bearing, plus some space for a belt spring. Print Settings Printer Brand: RepRap Printer: QuBD One-Up Rafts: No Supports: No Resolution: 0.2mm Infill: 25% minimum
thingiverse
NOTE: NOT FULLY TESTED YET - YMMV A Bowden extruder design for use with the One-Up/Two-Up printer models from QU-BD. Supports the Ubis-style hot-end that ships with those printer kits as well as "Groove-mount" style hot-ends such as E3D and Pico. ...
thingiverse
... ... It allows you to raise the board off your table to allow wires to run underneath and let you bolt it to your table and keep it in one place. Instructions No support needed to print the tab hole on the One-Up. ... Not sure about other printers.
grabcad
My new GEAR UP Project , is a bunch of gear and mechanism working together....this is Gear One, the first gear of many.
thingiverse
One UP mushroom from Mario with 3 STL files for Multi material printers like Prusa i3 MM. ... Not printed yet, I don't have the printer yet.
cults3d
one up lure mold 130mm a casting cone was made for the injector and a small reserve to avoid it being hollow when the lure is retracted a duct was also put to be sure that the product goes well to the bottom of the mold and especially to evacuate the...
thingiverse
On the one up when using this Gantry Replacement by Tony_921 I needed to add a belt tensonor, made the most sense to redesign the belt clamp. designed to use an 8-32 nut and bolt. ...since that's what I had on hand.
thingiverse
un petit remix du célèbre leurre Pour changer la taille jouer avec le scaling Peut être imprimer dans n'importe quel filament de preference sur la tranche
thingiverse
Fixes the heat seap on the two up and one up by directing the airflow of the fan around the extruder !!! Updated Version ( http://www.thingiverse.com/thing:972883 ) !!! ... Instructions Print with fan...
thingiverse
From the project of Dyhlt for the up plus one, and the help of ecati from sketchup comunit, here you will find and stl for enclosure for 3d up plus 2 with dimension of rear cover ajusted ! ... That's will be ok now to use this cover panel with rear...
prusaprinters
UP-mini-2-kalibrieren müsste auch für UP-mini _(den kleinen schwarzen)_gehen.
thingiverse
filament guide for the qu-bd one up / two up helps keep the filament from jumping out of the gear spur ;) Instructions clips onto the top of the extruder head. pops in easy if you push in the back side first. ... Please upload some pics if you print it...
thingiverse
This carriage / mount for Pico hot-end was designed to work with One-Up or Two-Up printers. ... update 7/7: fixed a handful of problems with the first version, and replaced all files with the updated v2 versionsupdate 7/8: fixed some stupid measurement...
thingiverse
This is a belt clamp for the extruder on the qu-bd one-up and two-up 3d printers. I do not have a 3d printer to test this yet, so any feedback is highly appreciated. It SHOULD fit well and allow the full range of movement for the extruder, however I...
thingiverse
The stock extruder on the One/Two up has a bearing arm that is made of very thin MDF board and is one of the things that usually break first on this design. This is a replacement. The smaller holes/slot may need to be drilled out and clean up with...
thingiverse
A) Base plate for One-Up/Two-Up printers that was missing from original Kickstarter kits (basicHEM_r3.stl). B) Alternative for QU-BD's design of the Y-drive mechanism that adds some sturdiness, allows the belt guide to operate more smoothly. Replaces...
thingiverse
A small pulley system, mod, for the one up two up 3d printers. Very quick print, you will need two of the top pulleys, and one bottom. This has no moving parts, so not technically a pulley, but more a cable guide. One small hole will have to be...
thingiverse
Clips straight onto your one-up / two-up Y-Bed so the parts don't jerk around in your footage. I'm using a £5 Tecknet webcam I got from a charity shop and some free software on my PC to make the timelapses. Going to buy a fisheye lens so I can get...
thingiverse
============================= If you print one of this, please take your time to take some pictures and tell me what you think of it and how it worked. ============================= I've made this today, and noticed that this duct can't hold...
thingiverse
So, I had some smaller linear bearings sitting around (shorter) and decided to beef up the bearing support for the bed, especially after adding my heat bed and the weight associated with it. I designed and printed a bearing holder to mount on each...