one up printer 3d models

I did not like the wood and cable ties so made bearing holder for the 2 main Z plate bearings and helps adjusts the 2mm off set in the incorrect cut - I also made a nicer looking extruder / hot end carrier that also holds the belt and snaps to the...

This pieces will hold your filament up of your One/Two up printer and it will fit any filament package size. You will save more room space just getting this 2 pieces together with your printer. It will fit your horizontal wood upper support. They...

This carriage / mount for Pico hot-end was designed to work with One-Up or Two-Up printers. ... update 7/7: fixed a handful of problems with the first version, and replaced all files with the updated v2 versionsupdate 7/8: fixed some stupid measurement...

Print Settings Printer Brand: LulzBot Printer: TAZ 6 Resolution: high speed, it takes long otherwise... Infill: diamond ...

... ctc. p.p.s: Some people have asked me if I can put one together for them. The answer is basically yes, but I have a real job, so if you have patience and can wait for a few days, I will be glad to put one together for you. ...Send me a message.

The parts are too large to print on a one up printer. ... Instructions Designed using AutoCAD

One UP mushroom from Mario Instructions Printed at 50% of the original size

I scaled this down to be small enough for a QU-BD One Up printer to handle. ...It seems to do the job just as well as the larger original.

One-Up / Two-Up Extruder

Part of UP! ...printer. ...It has been updated.

... than tape. I put it on my blog, too: http://swampcastle.blogspot.com/2011/12/filament-guide.htmlInstructionsReplace old filament feed mechanism on your Up! with this one, using the same bolt. ...Slip filament through slot, and you're good to go.

... than tape. I put it on my blog, too: http://swampcastle.blogspot.com/2011/12/filament-guide.html Instructions Replace old filament feed mechanism on your Up! with this one, using the same bolt. ...Slip filament through slot, and you're good to go.

I put it on my blog, too: http://swampcastle.blogspot.com/2011/12/filament-guide.html Print instructionsUnassociated tags: Up! Category: Parts Instructions Replace old filament feed mechanism on your Up! with this one, using the same bolt. ...Slip...

This is a spool holder. ... Instructions There is one screw hole in this part, this is to fix on the printer. ...We design two small protuberant parts on the shaft, one is to lock the ABS spool, the other is to stick on the printer.

There are 3 parts listed: * Test piece to check that it will fit on your printer (it should take around 5 minutes to print) * Main light bar (print 3 of theses vertically & hot glue / superglue them together ) * display bar to show percentage...

Full details are available here: https://vivalatina-shop.com/blogs/custom-made-jewelry/3d-printer-test-and-review This ugly-looking printer is an unusual beast. It is made from plywood, hardware, and stainless steel sheet and yet, gives professional...

ONE UP chainguide replacement

Lure mold one up 90

Copy of sawamura one'up shad silicone lure. More than 70 models - please contact. Модель силиконовой приманки в .stl. ...Более 70 моделей - обращайтесь.

Small coaster with the 1-up mushroom from Mario bross. Printed in PLA standard settings. no need for support. ...infill less than 10%

... a bowden extruder ! UPDATE V2: I needed mor space to let some screws slide under the bearing, plus some space for a belt spring. Print Settings Printer Brand: RepRap Printer: QuBD One-Up Rafts: No Supports: No Resolution: 0.2mm Infill: 25% minimum

... complicated processes. The result is a compact, robust and easy and logical assembly machine. Printing time of parts is below 20 h, the parts are simple in design and therefore easy to print. How I Designed This How to build MecaduinOpen One printer

It is meant to compliment the other One-Up and Two-Up pulley mods available here on Thingiverse. Why did I make this? Because I felt that the sliding door pulley is the superior method due to the simple fact it has a very simple tensioning system...

NOTE: NOT FULLY TESTED YET - YMMV A Bowden extruder design for use with the One-Up/Two-Up printer models from QU-BD. Supports the Ubis-style hot-end that ships with those printer kits as well as "Groove-mount" style hot-ends such as E3D and Pico. ...

New, really stable printer from U-Design Working area up to 300x300x300 BiB = Bigger is Better :) Nema23 Motors (high torque on XY axis) LM12UU Linear Bearings M10 & M12 Threaded rods (very stable frame) Highly recomended YRUDS extruder and new...

Here I have designed for you the Power Up or One Up mushroom. Of course, again for Led lighting. Eyes and face can be printed individually. Model fits on a 220x220 print bed. You have to drill the hole for the led output by yourself. So the model...

This uses an old UP extruder nozzle (one that was gummed up beyond repair) - or you can get the aftermarket ones from ebay for a few $. See instructions! Hope this helps someone! Instructions Use a...

Filament spool holder for Up! ...3D Printers with filament guide and cavity for filament filter. Support wide and thin spools. ...Must print two part2.

Summary all parts optimized & arranged for UP Printer´s build platform use the original AssemblyInstructions.pdf from Curriculum http://www.thingiverse.com/thing:404824/#files

all parts optimized & arranged for UP Printer´s build platform use the original AssemblyInstructions.pdf from Curriculum http://www.thingiverse.com/thing:404824/#files