onefinity drag chain 3d models

The priginal version was too close to the nut holding the bottom z axis bearing so I offset this one by about 10mm to give it better clearance.

Fits https://www.thingiverse.com/thing:568551 Top attachment is specifically designed for the 25mm version. The bracket fits all MPCNC models seamlessly. A standard 8x14mm aluminum rail, typically used for curtain hardware, serves as the...

I remade a few of the original Ortur laser mounts as they had weak points from there still being some seams on the models. I noticed this after one of my mounts cleanly broke right at a seam. I reworked them so they will be stronger and more...

Hi, Here is my holder for the angle Alu rail. The rail is from the hardware store and has the following dimensions: 30mm x 30mm x 1.5mm This way it fits exactly into the holder and there are no sharp edges after cutting. ...You simply place it on the...

Modified the clips slightly to allow for better fitment. ...For me, -0.2mm Worked perfectly but I also added a -0.4mm version.

This file is designed to be used as support for the dragchain by securing it in place with the MY3D printer's extruder assembly. ...The MY3D printer itself was built based on the Master Course of 3D Printing.

Customized version of https://www.thingiverse.com/thing:915487 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=915487

... **Wiring:** The design uses a simple drag chain for routing the wires. Consider using a more robust wiring system like a wire harness or a cable management system to reduce the risk of wire damage and improve the overall reliability of the system.

If your like me and didnt read directions about the chain being wider, then your pulling your hair about making 20 bigger links. These are the fools links, small link to big link connectors. You will need both. saves hours of printing more chains.

Cable Chain Mounts for a Direct Drive Elegoo Neptune 2 / 2S. ... See https://www.thingiverse.com/thing:6219861 for the direct drive mount

Customized version of https://www.thingiverse.com/thing:5780344 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5780344

This is a remix for the OneFinity hose mount that allows for a 4 inch hose. ...I paired it with the PWNCNC V7 dust boot, and the suction is amazing!

I added a spindle to my Onefinity and needed a taller solution for the hose clip. This will work with the bolts already in use. ...No need to get longer bolts.

Here's a bracket that can be screwed down into the table that a Onefinity CNC sits on and be used to clamp on a cardboard guard to shield the y-rails from chips and dust.

Bracket to hold extraction hose to OneFinity CNC. The "bump" allows the bracket to slip over the stepper motor cable. The cable needs to be unplugged first. ...I changed the stepper motor bolts to slightly longer versions.

... may need to be made if printed in another material.20% infill. I used supports on the bottom part of the circle. I did need to sand the bottom of the circle where the supports were to fine tune the fit of the circle into the Onefinity. ...

Use to hold X-Gantry of OneFinity CNC. Very useful when storing the CNC on vertical to avoid the X-Gantry falling down. Video Demo: https://youtu.be/MZpNQy9duFo If you found this useful, tips are always welcome. ... :D ...

I utilized a 10x10 drag chain from AliExpress: https://www.aliexpress.com/item/Transmission-Drag-Chains-3D-Printers-Parts-7-7mm-10-10-mm-Plastic-Towline-Part-1M-Cable/32813659240.html?spm=a2g0s.9042311.0.0.pvmvUB to manage cables efficiently. A bar...

The original design didn't allow for the customization I needed - the OneFinity has a really tight clearance between the spindle and the Z-axis (< .5 inches) which required some squeezing to make everything fit. Should work for any CNC with a 65mm...

Terminal for heated bed drag chain for Artillery Sidewinder X1. ...(80mm/V4)

this is a new model inspired by Greecher's (https://www.thingiverse.com/thing:4878007)model for a light ring to mount on my Makita router for my onefinity cnc. Greechers model was good but didn't work for the headlight led's that I ordered. You'll...

It was designed with FRC in mind.This is a WIP, yes that includes the hurried render ;).I designed this enclosure for the Onefinity woodworker CNC. More info on the machine can be found here. https://www.onefinitycnc.comIt uses t-slot aluminum...

It was designed with FRC in mind.This is a WIP, yes that includes the hurried render ;).I designed this enclosure for the Onefinity woodworker CNC. More info on the machine can be found here. https://www.onefinitycnc.comIt uses t-slot aluminum...

this is a new model inspired by Greecher's (https://www.thingiverse.com/thing:4878007)model for a light ring to mount on my Makita router for my onefinity cnc. Greechers model was good but didn't work for the headlight led's that I ordered. You'll...

a remix with holes for IGUS drag chain. ... I also made a Version with not so small bend radius for the Igus-drag chain. ...https://www.thingiverse.com/thing:4926280

drag chain mount for the Galileo 1.5 (Orbiter) Extruder for Igus drag chain and Voron 2.4 use long screews to mount the Orbiter and the Motor and mount the drag chain mount with 2 M3 Hexnuts. ... Use the "Main_Body_Orbiter_4mm_Extended" from there...

This is a remix of Drag Chain - Cable Chain - Ender 3 by diogosantos88 Part: Support 2 https://www.thingiverse.com/thing:3715002

This is a remix of Drag Chain - Cable Chain - Ender 3 by diogosantos88 Part: Support 2 https://www.thingiverse.com/thing:3715002

This is a complete Cable Chain / Drag Chain for thee Ender 5 You will need : 1 meter 19x10mm Chain - (I bought as sizing is perfect (you can also print) 1 meter 15x10mm Chain - (I bought as sizing is perfect (you can also print) 2 x spring washers...

I am running a spindle and this cable chain system: https://www.thingiverse.com/thing:4619804 with this hose: https://www.homedepot.com/p/RIDGID-1-7-8-in-x-10-ft-Pro-Grade-Locking-Vacuum-Hose-Kit-for-RIDGID-Wet-Dry-Shop-Vacuums-LA2570/305626336. This...