op 1 stand 3d models
1015390 3d models found related to op 1 stand.thingiverse
I've been working on a design for an OP-1 stand for a couple of weeks now, and I think it's finally at the point where I should show it off a bit! This has been quite a fun project, and one that I am quite pleased with the outcome of. As mentioned in...
thingiverse
There is nothing binding the stands with the OP-1 except gravity. It sits at 15 degrees and is very comfortable to play on. Way better than leaning way over the OP-1 to see the screen. The stands are virtually invisible while the OP-1 is mounted. So...
thingiverse
15 degree Angled Standoff for a Teenage Engineering OP-1, for better Handling on the Table. Flatmounting the OP-1 to the holder and holes for Rubber Feets on the Ground of the Holder. Screwmounted. ... Print Settings Printer: ...
thingiverse
A stand designed for TEENAGE ENGINEERING OP-1 based on https://www.thingiverse.com/thing:33332 *tested and it fits perfectly. ...will upload more pictures *Two circular holes on the bottom are for circular plastic washers to use as stoppers from...
thingiverse
I wanted to design a very low profile stand that gets out of the way and doesn't interfere with the metal aesthetic of the OP-1. The stand simply plugs into the screw hole behind the OP-1 to hold the device in place. The small fixed bolt on the stand...
thingiverse
These little guys act as a stand, tilting the OP-1 up just a bit, which I like, and securely holding your phone, including a small case like I have here. For the big 'plus' models, you just clip between the knobs shown, for smaller phones, just...
cults3d
These little guys act as a stand, tilting the OP-1 up just a bit, which I like, and securely holding your phone, including a small case like I have here. For the big 'plus' models, you just clip between the knobs shown, for smaller phones, just...
thingiverse
Simple OP1 stand for all seasons! No assembly required, print as many as you wish and enjoy :) PLA or PETG Give a shout out and upload your photos! ...Print Settings Rafts: No ...
prusaprinters
Simple stand, adjustable to give you access when using it in "low mode" and reversible for a "high mode." M3x16mm bolts into M3 nuts. A and B are simply mirrored versions, because I wanted the aesthetic of having the screw caps on the outside. The...
thingiverse
Some People Just Have Both. ... Why not have them together? Literaly. An OP-1 x OP-Z Hybrid Stand fot thoes who just have both. ...
thingiverse
I found the original stands were slightly too thick to fit in the box with the OP-1 so I slimmed it down without adjusting any of the holes or features. It's roughly 25% thinner and when placed flat on the OP-1, will let you close up the paperfoam...
thingiverse
Instructions Print stand with thick wall (1.5mm in my case) with 0% fill. Print screw with 100% fill, and as the hot end reaches the top layer, you might want to speed up or slow down the process to prevent hot end melt and mangles the thread...
thingiverse
A simple stand for the Teenage Engineering OP-Z. Lifts it off of the table/desk and gives it a slight tilt. V1 - Print on its right side with 'supports everywhere' to handle the pitch mod cutout. ... V2 - Print upright, no supports needed Back-only...
thingiverse
3D Printer friendly OP-1 Accessories. ... Better results with <= 0.2 layer height.
grabcad
There is a pocket for the accessories, and the USB cable fits on top of the OP-1 keyboard when closed. The ports can be used while keeping the OP-1 in the case itself. ...There are slots on the outside to use the elastic bands to keep the case closed.
thingiverse
A clip I quickly designed, to hold down the record and shift keys on the op-1. Pushing the bottom of the clip, lifts the key, allowing you to try recording again without removing the clip. Works with any key on the edge of the op-1. I'm selling a...
sketchfab
I decided to model one of my favorite synthesizers, the OP-1. This thing, despite it’s deceiving size, is a beast when it comes to producing music, and with it’s limitations it encourages you to stay creative! ...I’d love to own a unit one day, albeit...
thingiverse
This is modeled after the original OP-1 knob using a good ole' caliper and patience. ...I did my best to recreate the plastic spring from the original in order to maintain snugness, and I'm pretty happy with the result at least from my printer.
thingiverse
This is a customised easy print version of the Teenage Engineering OP-1 Crank. The only non 3D printed part required is the [Lego Technic Pin 1/2](https://www.bricklink.com/v2/catalog/catalogitem.page?P=4274) The Lego pin is the easiest way to have...
thingiverse
A sturdy and lightweight case for your OP-1! If you flip your device around, you will get a nice rack. Inside the case, there is space for two drawers where you can put your cables and accessories. On the bottom, there are indents for optional...
thingiverse
This is a customised easy print version of the Teenage Engineering OP-1 Brick Shaft. The only non 3D printed part required is the [Lego Technic Axle 2](https://www.bricklink.com/v2/catalog/catalogitem.page?P=32062) The Lego axle is the easiest...
thingiverse
Here is a sweet looking hard case to protect your precious OP-1 from Teenage Engineering. I've printed this using a Mark Forged Onyx 1 in Onyx using the default settings and it came out absolutely perfectly. I'm using a 5mm x 300mm stainless shaft...
thingiverse
Customized version of http://www.thingiverse.com/thing:345972 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=345972 Instructions Using the following options: length = 20 height = 3 flat = 0 width = 1
thingiverse
A stand designed for TEENAGE ENGINEERING OP-Z *not tested yet (Not having the device yet!) but should fit because it's designed based on sizes from a working one *Two circular holes on the bottom are for circular plastic washers to use as stoppers...
myminifactory
Better yet, the OP-1 BestCase is both a deck protector and a stand that tilts the OP-1 up to take advantage of the same ergonomic benefits that computer keyboards have been rocking since the 80's. The model includes round tabs at each corner to...