open tools 3d models

Use these soft plastic tools to safely pry open devices without scratching the case, glass, or internal components. Built in a pair of two different styles - a wide tool with a thin tip that's great for getting underneath glass and in thin cracks,...

Opening for certain devices.

Casio watch opening tool for battery replacement / maintenance. ...Diameter of back plate: 37mm

Watch opening tool for diameters of around 33-35mm. ...It has various holes for leverage.

the sim opener tool thingy. ... is very small so might be a little difficult to print I used the measurements for the opener for the Huawei P20

Mobile phone or tablets opening tool. ...Print Settings Printer: Prusa i3 Rafts: Doesn't Matter ...

I bought a watch case opening tool from China, but the case it came it was horrible. All the attachments fall out all the time, so I designed a new case in Tinkercad. ... The case closes with 5x5mm magnets.

Mobile phone, tablets or enother consumers electronics opening tool Print Settings Printer: Prusa i3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Notes: I printed it ABS

Parametric Watch Opener Tool Parametrize in Customizer to make it fit your watch. ... Remix of: - Customizable watch opener by blackboots - Seiko Watch Case Tool by Chuckdotdot Improvements: - Slightly more customizable than blackboots' version -...

Finalized version of a XT90S opening tool, for smooth opening of XT90S connectors, to avoid damaging what's in the other end of the wires (battery/ESC) It has evolved from the initial wedge opener https://www.thingiverse.com/thing:4775717 and the...

Parametric Watch Opener ToolParametrize in Customizer to make it fit your watch.Remix of:Customizable watch opener by blackbootsSeiko Watch Case Tool by Chuckdotdot Improvements:Slightly more customizable than blackboots' versionChamfer on...

i needed a place for all my opening tools and since i tend to misplace stuff ill know if im missing something with this tray. i hope yall can get some use out of this!printed on a Prusa miniFilament: PLAlayer height: 0.15infill: 10%-15%nozzle...

Tools to open the nuts from the antenna connector, the channel switch and the volume switch. 15.02.2019 new 2 in 1 Tool added. ... I printed it with PLA, 100% infill

If you happen to have this Klarstein Mixer, chances are that you can't open the blade holder at the bottom by hand. I've created this simple tool that does the job perfectly. Also added two holes on the back for two small neodym magnets (to attach...

Copy of an original Nokia tool for opening devices.

Tool to open Suunto Stinger dive watch / computer. ...Not great but it works.

... have the same diameter of 486 mm. The actual Jug lid opening is slightly larger to allow for movement of the tool and variances in printers. ...If you have a different design lid and need a tool designed for easier twist opening please reach out.

In Corona Time this is the best tool to open doors and other things..... NEW VERSION! https://www.thingiverse.com/thing:4319666 1. two kind of door opener 2. beer opener 3. Pin for use Buttons like Card Terminals or other 4.

... routinely. After a while it gets really hard to open by hand so we have to hit it with a wrench to loosen it or use channel locks. One of my coworkers said, "If only someone could 3D print a tool to open these easier....". ...Well here it is.

Be me, an intellectual, It's finaly my 21'st birthday, Ordered 6 kegs of beer to drink with all my friends, Find out with dispair that you need a special tool to open them, Quickly reverse engineer the tool in Fusion 360, Print it in PLA at 215 with...

This is a simple tool to open the plastic conduit that comes with the Tevo Tornado. I tried removing some with my fingers and it hurt. This little guy can open the conduit so you can get the wires out. I am replacing my plastic conduit with meshed...

I needed a tool to open 360's and got sick of making then from random plastic things. This is well reinforced for little breakage, prints quick and works well with PLA. I know the B needs to be fixed, but meh. No Supports or anything, printed...

I designed a simple tool to open the back of my Casio watch. It should work on a lot of other models too. If the back plate is really tight you can use the lever to untighten it. It is designed for a back plates diameter of 39-40 mm. ... Happy...

I designed a simple tool to open the back of my Casio watch. It should work on a lot of other models too. If the back plate is really tight you can use the lever to untighten it. ...It is designed for a back plates diameter of 39-40 mm. Happy printing...

So, I designed this little tool to slice the bags open. It clamps onto the edge of a table, up to 1.75" (45mm) thick, using a 1/4"-20 bolt with hex nut, and accepts an X-Acto or similar knife blade through a slot in the top to do the slicing. ...

I wanted a tool to open doorhandles (lever ones only) and push buttons without me touching them. This is an early prototype, sized to fit on my small printer at a 45 degree angle. I used some coat hanger wire to make a loop, and mounted it on a...

This is a tool to get into the older white xbox 360s. ...Note, I don't have a 3d printer (yet) or one of these tools. ...If anyone would like to print one out and check it, I'd love to know if it works :-)

This is a simple tool to make it easier and safer to unscrew the bezel of the A2S / A2 and similar flashlights like the Thrunite TH30 (only tested on the A2S)

It took me a while to figure out that with a 3D printer I can make my own tools, and being plastic, there's no chance of scratching them, so rather than buying a tool to do it myself, I made a quick design in solidworks and tried it out, and...

It has small slider for opening and closing hook. Compact and advanced design. Two versions small and large. Small ring outer diameter 50mm, inner 26mm, griping diameter 35mm. Large ring outer diameter 65mm, inner 41mm, griping diameter 50mm. ... ...