openastrotracker 3d models

I got a little over-zealous tightening a set screw that holds the RA belt in place and cracked the end of the split ring, forcing me to reprint that part. Determined not to repeat the mistake, I remixed both parts to close the gap, ensuring it...

Modified parts have been altered to accommodate the use of more common 608 ball bearings. Both split-rings must be printed with supports enabled in order to achieve optimal results. The ball bearings on the roll-mounts require insertion into the...

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

After several difficulties with last attempts to take photos with the OAT, some points still bothered me during the setup. To align the azimuth axis, the substrate must be forced in the spirit level to get no further inaccuracies when adjusting. ...

I could've simply reached down into the front openings of that 30-degree angled piece, but my driver was too short to grasp those screws at the back. This revised design eliminates unnecessary material, making it a breeze to access the rear screws...

I found that the in lower latitude versions of OAT, RA stepper motors clash with the bottom mounted MKS case. So, I designed a case that is mounted at the rear of the oat to prevent this issue from coming up in the first place, irrespective of the...

... on the lid to slide the gps antenna into. It is a tight fit and may need a little heat to flex the plastic the first time but you want it tight. Thanks Remix of OpenAstroTracker - DSLR tracking & GoTo mount https://www.thingiverse.com/thing:4472727

This is my custom enclosure for the OpenAstroTracker open-source motorized sky tracker for DSLR cameras. Details for this project can be found here: https://wiki.openastrotech.com/ I was looking for a compact enclosure for the minimalist...

UPDATE: New designs for my case are now uploaded, thoroughly tested with both Uno and Mega boards, as well as small and large buck converters. The SCAD file is also available for download, allowing you to customize the case by removing openings for...

I upgraded the pole mount and all four poles to support a robust 6001 bearing, replacing the standard 6801 bearing that was initially specified for these components.

This assembly included a modified mount used twice (front&back) for a 500mm Walimex lens. Assembly includes: - one mount that integrates a focuser assembly - focuser assembly driven by a small stepper motor 28BYJ-48 - Camera mount is for...

This is a modified RA motor mount for 40 degree latitude. The original mount with NEMA motors used to intersect each other. The non-40 degree mount with motor fixed below would interfere with the aluminum extrusion. ...So the opening for the motor was...

I tried printing the current desighn but the base that holds the mks pcb is so thin it just broke apart, i edited it and made the base an extra 4mm thick. ...currently printing new model,will upload pic of finished item later.

Since the Canon EF 70-200mm F2.8L IS II USM is quite bulky, I designed an additional mount to support the front of the lens.Just use two M4x12 and two M4 T-Nuts and slide on, after mounting camera & lens on the OAT.

60mm bubble level holder for OpenAstroTracker 2020 build.

A large M14 locking ring. ... Designed to lock the level adjusting feet on my OpenAstroTracker.

A bahtinov mask that fits to the Improved OpenAstroGuider scope (add-ons of the OpenAstroTracker).

This is a laserpointer holder for the OpenAstroTech tracker. ...It helps to polar align the mount. More information an tracker: https://wiki.openastrotech.com/OpenAstroTracker. ...Laserpointer 15mm diameter.

Case is remixed from : https://www.thingiverse.com/thing:4253325 GPS and Gyro holder from : https://github.com/OpenAstroTech/OpenAstroTracker/blob/master/Addons/DigitalLevel/STL/Digital%20Level%20And%20GPS%20Holder.stl Camera support from :...

compact case for motor and controler no need to print extra piece, can be mont on original OpenAstroTracker https://www.thingiverse.com/thing:4167783 Add "facade v5" with gap 0.5mm for mounting

Ball head laser pen holder (303 or similar) for OpenAstroTracker. ... Ball head was remixed from https://www.thingiverse.com/thing:3467378 The handle comes in two variants: - integrated with the ball - divided into two parts for easier printing ...

Knob M14 small created for the open astro tracker M14 Bolt, Bolt Level Lock Nut and Bolt Level Feet from Remix+of+OpenAstroTracker https://www.thingiverse.com/thing:4472727

... lid has been changed to include a cable clamp / strain relief for the USB lead. ...The parts amended with ‘JC’ replace their counterparts on the OAG GitHub. https://github.com/OpenAstroTech/OpenAstroTracker-Addons/tree/master/OpenAstroGuider

Used for astrophotography sky tracking - power distribution and stepper motor control.Based off https://wiki.openastrotech.com/OpenAstroTracker firmware but modified for a full size equatorial mount. ...Use PHD2 guiding for tracking.Fan:...

Svbony SV165 guidescope using a Sony imx-291 Astrophotography could be a expensive hobby in someways just looking for cheaper alternatives modified a few pieces from the openastrotracker community to make this cam cover for this guidescope enjoy. ...

... camera dovetail mount. Printed to allow me to use this camera on OpenAstroTracker. The bracket is fixed to the camera using 4 M4x12 screws. ... The design includes a top post that is intended to protect the USB3 cable from being broken off.

You can trim the excess belt, or leave as is if you need to adjust later. This was designed to be used with my OAT Focuser:https://www.prusaprinters.org/prints/150513-openastrotracker-focuserbut it could be used for anything that needs a loop of...

K-mount adapter that lets you mount the IMX290 from the OpenAstroGuider V2 (https://github.com/OpenAstroTech/OpenAstroTracker-Addons/tree/master/OpenAstroGuider) . Flange focal distance is rough, on my lens it achieves infinity focus with room to...