optical drive rails 3d models

This guide demonstrates how to fit a 3.5" hard drive into a 5.25" optical drive bay by using the dimensions from two standards: SFF-8301 for the 3.5" disk drive and SFF-8851 for the 5.25" optical drive. You can choose to print either a full sled with...

I used dimensions from the following two standards: 3.5" disk drive: SFF-8301: ftp://ftp.seagate.com/pub/sff/SFF-8301.PDF, 5.25" optical drive SFF-8851: ftp://ftp.seagate.com/sff/SFF-8551.PDF. You can print either a full sled with a base plate or...

Optical drive holder

Slim optical drive enclosure not rigorously examined yet.

A simulation of an optical drive tray for use as a coaster. ...Measures 3.56 in x 2.54 in x .14 in.

An optical drive compartment is included in the xPredator chassis design, providing convenient storage and access to your CDs, DVDs, and Blu-ray discs.

A simulation of an optical drive tray for use as a coaster. ...Measures 3.56 in x 2.54 in x .14 in.

The thicker component accommodates older optical drives used in laptops that are slightly thicker than their modern counterparts, making it the ideal choice for these types of drives. In contrast, the standard component is specifically designed for...

Simple frame to hold a laptop sized optical drive with holes for screws to attach a top and bottom plate. ...Its a really tight fit so it should hold the drive itself in place without any screws.

This is a simple way to turn your UJ-875 internal laptop optical drive into an external one. You will also need a JAE 50-pin to USB adapter to get started. Use it as is or give it a professional look by finishing the top and bottom with profile cut...

This is a mount designed specifically for optical drives that can be securely fastened under the desk. With my case now upgraded to one without any 5.25" drive bays, I had no choice but to position my drive outside of it. Given that I was already...

HHD Rails.

... this as a means of replacing Rails, with no focus on optimizing printing - only the model. ... Make certain that the flat side intended for drive support is positioned correctly on the print bed, as these were rotated when I imported them as STLs.

Things to note: I used a Crucial BX500 for determining the drive hole spacing, your experience may differ if you use a different brand drive. It should work...but... When installed into the Pro case the drive will actually a little slanted in the...

5.25" optical drive (or whatever 5.25") mount for original Enthoo Evolv enclosure (do not know if this will fit to Evolv X or newer). ...

This is a blank for an optical drive on the Lenovo Thinkpad T420 laptop.(model number GT50N) I got the bottom measurements from Ollie242's project on putting a raspberry pi in the same laptops optical drive...

This Pioneer BDR-209EBK optical drive was precisely measured utilizing a steel rule and vernier calipers. ...As it was not taken apart, certain internal components or challenging-to-reach regions might exhibit slight deviations from the specified...

In my define 7 the optical drive has a silver body, and that looks awkward through the window. So I designed a cover, which now will be held in position with three magnets. The holes are designed for magnets, 8mm diameter and 1mm height. You...

DVD player housing - Laptop DVD player If you have a HP laptop Optical drive (127 x 128 mm) and a cable to USB : To be able to use an older HP laptop DVD player stand alone. Allthough the player works without a housing, it is nice to have it...

Rails for a vintage 5.25 inch optical drive perfectly match the A950-TWR model of the Packard Bell computer, and careful inspection confirms they are designed to fit seamlessly into place.

... by utilizing two 6-32 flat head screws per rail for secure attachment. McMaster-Carr part # 90272A146 may be a suitable alternative. The rails fit flawlessly into the chassis, with latches snapping in correctly and maintaining drive stability.

Added a 5.25 drive to my 486 project and needed rails to mount properly. Need support for single overhang hook. ...I painted a custom support with slicer, hope this helps someone else.

This is an universal 3.5' hard drive rail for PC cases. It is made as short as possible to fit 10x10x10 3d printers (crosswise). ... Size is: 4mm x 12mm x 113,6mm Screw holes are 101,6mm apart.

I needed some generic plastic drive rails that fit the standard 3.5-inch hard drive. They are ridiculously easy to find online, and they work amazingly well - I'm really pleased! ... **Printing Details** PLA Filament: 0.3mm layer height | Printing...

Easy to print, faceplate for antec 300 optical drive.

Gear wheel for repurposing the stepper motor found in optical drives.

A rapid locking system is featured in the xPredator case's optical drive rack, ensuring quick and efficient use.

Cover for the optical disc drive bay, for Dell optiplex 7020. ...probably also works for other models.

... standard-sized slimline SATA Optical Drives and convert them to USB via a slimline SATA to USB adapter. Two screws were used on the sides to secure the optical drive, but it could be used without them due to its snug fit with very slight give.

Lenovo m93p SFF optical drive cover grill. ...Press fit so it does not need any sort of glue to fix it in place.